PowerPCM_Flasher: my tool for E38 and E67
-
- Posts: 583
- Joined: Thu Feb 13, 2020 11:32 pm
- cars: Mainly GM trucks, a Cruze and an Equinox for dailys..
Re: PowerPCM_Flasher: my tool for E38 and E67
Thanks for all the updates!!! I have the same issue disconnecting, need to close the program and restart it.. Normally when using it with tech2win,gds2, or gm sps the MDI stops flashing when it's done, with this program it keeps flashing so something is a little glitchy with that, but I am NOT complaining!!!
I will try to give it some more of a workout this weekend given enough spare time..
Oh, 1 thing to mention to Antus, do you have any resistors added to the can circuits? In the vehicle there are 2 120 ohm resistors added to the end of the circuits.. I just added one across the legs coming out of the ECM, not sure if that might be why your having connection issues?? I do know in car when one end is disconnected it makes all the data very glitchy with the scan tool..
Um... I just tried to get 005 version just so I have it, where'd it go??? No download link at all? or am I just having vision problems...
I will try to give it some more of a workout this weekend given enough spare time..
Oh, 1 thing to mention to Antus, do you have any resistors added to the can circuits? In the vehicle there are 2 120 ohm resistors added to the end of the circuits.. I just added one across the legs coming out of the ECM, not sure if that might be why your having connection issues?? I do know in car when one end is disconnected it makes all the data very glitchy with the scan tool..
Um... I just tried to get 005 version just so I have it, where'd it go??? No download link at all? or am I just having vision problems...
-
- Posts: 397
- Joined: Wed Jul 05, 2017 8:30 am
- cars: 2001 Pontiac Grand AM SE
LD9 2.4l I4, 4T40E
2005 Chevrolet Venture
LA1 3400 V6, 4T65E - Location: North TX, USA
Re: PowerPCM_Flasher: my tool for E38 and E67
Hi all;
I THINK it was below one of the two pictures that have been removed in the first post!
Mike
I, Too do not see a download link any more.......ironduke wrote:
Um... I just tried to get 005 version just so I have it, where'd it go??? No download link at all? or am I just having vision problems...
I THINK it was below one of the two pictures that have been removed in the first post!
Mike
-
- Posts: 51
- Joined: Wed Feb 19, 2020 9:58 pm
Re: PowerPCM_Flasher: my tool for E38 and E67
The vision problems has been on my side
Fixed the link and the pictures in the first post
Ok, so lets try if disconnecting is better with that release or what the error is.
Fixed the link and the pictures in the first post
Ok, so lets try if disconnecting is better with that release or what the error is.
-
- Posts: 583
- Joined: Thu Feb 13, 2020 11:32 pm
- cars: Mainly GM trucks, a Cruze and an Equinox for dailys..
Re: PowerPCM_Flasher: my tool for E38 and E67
Thanks for fixing the link.. Don't have an E38 on the bench at home(yet) but trying the MDI with another spare ecu I have(12611549) and it still doesn't disconnect correctly.. In fact, even with just the MDI connected I click init and select the MDI and then click disconnect and the MDI is still connected.. Not a huge deal, I'll gladly live with it, lol.. I'm sure it might be bugging you a little bit though.. Nothing in the log screen, anything I can do from my end to help?
initialising Tool J2534 PassThru
Bosch - MDI...
ok.
disconnect all tools...done.
initialising Tool J2534 PassThru
Bosch - MDI...
ok.
disconnect all tools...done.
- antus
- Site Admin
- Posts: 8253
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: PowerPCM_Flasher: my tool for E38 and E67
Still connects and reads fine, but this error on disconnect:
Code: Select all
upload progress: 94% (0x1E0000)
upload progress: 97% (0x1F0000)
upload progress: 100% (0x200000)
done.
validating upload...ok, valid.
disconnecting...stop periodic CAN NOT ok: 13
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 51
- Joined: Wed Feb 19, 2020 9:58 pm
Re: PowerPCM_Flasher: my tool for E38 and E67
Ok, is see the problem.
The Volvo Dice will just stop all periodic messages with an empty parameter.
The MDI not, it seems to need the Address of the periodic message (0x7DF - Tester Present).
That can be fixed easily, but tomorrow
It is 1am here...
Thanks for fast testing you both.
The Volvo Dice will just stop all periodic messages with an empty parameter.
The MDI not, it seems to need the Address of the periodic message (0x7DF - Tester Present).
That can be fixed easily, but tomorrow
It is 1am here...
Thanks for fast testing you both.
-
- Posts: 583
- Joined: Thu Feb 13, 2020 11:32 pm
- cars: Mainly GM trucks, a Cruze and an Equinox for dailys..
Re: PowerPCM_Flasher: my tool for E38 and E67
Found my key!!!! lmao, shoulda tried the seed.. That was the key..
but with version 005 load,check, and save is missing from the gui???
but with version 005 load,check, and save is missing from the gui???
-
- Posts: 51
- Joined: Wed Feb 19, 2020 9:58 pm
Re: PowerPCM_Flasher: my tool for E38 and E67
Look at the menu bar i integrated, under file.
-
- Posts: 583
- Joined: Thu Feb 13, 2020 11:32 pm
- cars: Mainly GM trucks, a Cruze and an Equinox for dailys..
Re: PowerPCM_Flasher: my tool for E38 and E67
DOH!!!!!!!!!!!daniel2345 wrote:Look at the menu bar i integrated, under file.
ok.. I got it.. lmao..
still can't seem to fix my brick.. somehow I wrote to the section before 0x10000 and screwed up the seed/key and I cannot seem to undo it..
I'm good like that, I can break stuff that doesn't need to be broken.. but it's always a learning experience.. lol.. I do have another E38 to put on the bench if all else fails.. Not giving up though..
Re: PowerPCM_Flasher: my tool for E38 and E67
My pops used to say "If you haven't broken anything then you haven't done anything."
So you must be doing something ...
Awesome work on your PowerPCM Flasher daniel2345, awesome!
Curious what language you working in, I noticed your comment about classes ... C??
So you must be doing something ...
Awesome work on your PowerPCM Flasher daniel2345, awesome!
Curious what language you working in, I noticed your comment about classes ... C??
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!