VZ E55/E40/E38 ECU LINKER
Re: VZ E55 ECU LINKER "SRAM CODE READER"
yeh barina or corsa c was dual, can bus on back end between modules and kline on front end, it's confusing
Re: VZ E55 ECU LINKER "SRAM CODE READER"
There is a k-line datapin on E55 but I have not got the ecu fully talking on that yet. Its also mentioned in our Saab E55 ECU documents.The1 wrote:There's no Kline data pin as far as im aware.
That's neat So it's expecting an input on PID 6C, the string looks like the pin so you have to have the correct pin to start with?
What immo data does it send out? Im guessing it's like that 4 chunk of data that gets sent on relink.
E69 on the other hand is very talkative and we can also upload a bootloader via k-line for full access
E55:
Code: Select all
ME9.6(HFV6) Pin (Bosch) Pin (GM) Connector
Can H V23 J2-23 Conn 2
Can L V55 J2-55 Conn 2
Plus 12v V03 J2-03 Conn 2
Plus 12v V36 J2-36 Conn 2
Ground Chassi/Pin25 Conn 2
K-Line V38 J2-38 Conn 2
GPT2 E04 J1-04 Conn 1
GPT1 E21 J1-21 Conn 1
ME(D)9.6.1 Pin (Bosch) Pin (GM) Connector
Can H 42 J2K42 2 (Small)
Can L 55 J2K55 2 (Small)
Plus 12v 54 J2K54 2 (Small)
Plus 12v 56 J2K56 2 (Small)
Ground 1 J2K01 2 (Small)
K-Line E47 J1A47 Big
GPT2 E07 J1A07 Big
GPT1 E30 J1A30 Big
Re: VZ E55 ECU LINKER "SRAM CODE READER"
Yes already communicating on Klinemackan wrote:There is a k-line datapin on E55 but I have not got the ecu fully talking on that yet. Its also mentioned in our Saab E55 ECU documents.The1 wrote:There's no Kline data pin as far as im aware.
That's neat So it's expecting an input on PID 6C, the string looks like the pin so you have to have the correct pin to start with?
What immo data does it send out? Im guessing it's like that 4 chunk of data that gets sent on relink.
E69 on the other hand is very talkative and we can also upload a bootloader via k-line for full access
E55:E69:Code: Select all
ME9.6(HFV6) Pin (Bosch) Pin (GM) Connector Can H V23 J2-23 Conn 2 Can L V55 J2-55 Conn 2 Plus 12v V03 J2-03 Conn 2 Plus 12v V36 J2-36 Conn 2 Ground Chassi/Pin25 Conn 2 K-Line V38 J2-38 Conn 2 GPT2 E04 J1-04 Conn 1 GPT1 E21 J1-21 Conn 1
ME(D)9.6.1 Pin (Bosch) Pin (GM) Connector
Can H 42 J2K42 2 (Small)
Can L 55 J2K55 2 (Small)
Plus 12v 54 J2K54 2 (Small)
Plus 12v 56 J2K56 2 (Small)
Ground 1 J2K01 2 (Small)
K-Line E47 J1A47 Big
GPT2 E07 J1A07 Big
GPT1 E30 J1A30 Big
Found the code at the same address but not the immobilizer data
Very slow at the moment
Any ideas on how to speed it up?
i coudnt get j2534dotnet to work either
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VZ E55 ECU LINKER "SRAM CODE READER"
nice work
Re: VZ E55 ECU LINKER "SRAM CODE READER"
Just found Seed key pairs for Security 01 (SPSrequest) and 03 (DevCtrlrequest)
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
- hsv08
- Posts: 547
- Joined: Thu May 09, 2013 6:50 pm
- cars: (EX) VT SENATOR 355 STROKER
(EX) VT SS 304 MANUAL
NOW VX V6 HACK
Re: VZ E55 ECU LINKER "SRAM CODE READER"
I love where this is heading. Good work boys.
Re: VZ E55 ECU LINKER "SRAM CODE READER"
Tested on 5 OS
Nothing special on security 2
It looks like Kline gives you access to areas that CAN cant
J2534dotnet works with Kline
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VZ E55 ECU LINKER "SRAM CODE READER"
Seems to reading just fine. Immo data is however not the same as Carprog reports. Will try to get my hands on a V6 Saab here to check some more results.
Using a modded Mangoose (Mongoose) Pro 2 GM clone. The chinese could not get the canbus connected properly so I've had to reroute it...
Using a modded Mangoose (Mongoose) Pro 2 GM clone. The chinese could not get the canbus connected properly so I've had to reroute it...
- Attachments
-
- Capture_cad.PNG (22.46 KiB) Viewed 6043 times
Re: VZ E55 ECU LINKER "SRAM CODE READER"
Can you do a read of the default addresses and send me the file please
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VZ E55 ECU LINKER "SRAM CODE READER"
i had this with barina, requesting a PID with level1 vs level2 access gave different results