Ve Software

Programs / Tools / Scripts
mattyjf01
Posts: 282
Joined: Wed Sep 04, 2019 8:41 pm

Re: VE V6 ECU LINKER

Post by mattyjf01 »

While testing on an E39 today i noticed if you turn the ignition off for 20 seconds then on again after a reset or link it saves to flash.
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: VE V6 ECU LINKER

Post by The1 »

i think the relink worked on both your tool and tech2 for this E69 VE, this car has other issues, it's cranking and no dash messages other than stability issue (prob rear sensor as known) so it should run, ive read in quite a few places that the "P0633 Immobilizer Key Not Programmed – ECM/PCM" is logged after relinking and goes out once engine is started. I have other fault codes coming up now on this car P0197,118,193,222,122 so ill be chasing down another circuit, this car blew the capacitor off the circuit board on the battery terminals inside the ecu and blew the F35 20amp odd coil circuit fuse. :o
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: VE V6 ECU LINKER

Post by The1 »

Car is up and running, both tools working successfully on E69
mattyjf01
Posts: 282
Joined: Wed Sep 04, 2019 8:41 pm

Re: VE V6 ECU LINKER

Post by mattyjf01 »

*1/04/22 V0.02
-Added HVAC Single/Dual Zone programming
-Added SIC Sports/Standard mode programming and Vin read/write
mattyjf01
Posts: 282
Joined: Wed Sep 04, 2019 8:41 pm

Re: VE V6 ECU LINKER

Post by mattyjf01 »

V0.04
-Added IPC Config Programming

Went onsite to do an IPC and EHU
Neither Tech2, Autel or Launch could change EBCM type in the IPC
To get the job done i used my SWCAN VIN programmer for seed key unlock and launch for the config programming :thumbup:

So added the function today
IPC.png
IPC.png (17.37 KiB) Viewed 9156 times
Whiteford
Posts: 30
Joined: Mon Jan 21, 2019 10:35 am
cars: Ford Falcon

Re: VE V6 ECU LINKER

Post by Whiteford »

mattyjf01 wrote:V0.04
-Added IPC Config Programming

Went onsite to do an IPC and EHU
Neither Tech2, Autel or Launch could change EBCM type in the IPC
To get the job done i used my SWCAN VIN programmer for seed key unlock and launch for the config programming :thumbup:

So added the function today
IPC.png
Have you uploaded a download link for V0.04?
UCMatt
Posts: 86
Joined: Mon May 11, 2009 4:00 pm
cars: VE Sportwagon
VYExec
VN V8 UC Torana Hatch

Re: VE V6 ECU LINKER

Post by UCMatt »

Looks awesome! :thumbup:

I have a VE that I am currently converting from V6 to V8.
Perfect candidate to test your software on.

Has the download link been shared yet?
mattyjf01
Posts: 282
Joined: Wed Sep 04, 2019 8:41 pm

Re: VE V6 ECU LINKER

Post by mattyjf01 »

UCMatt wrote:Looks awesome! :thumbup:

I have a VE that I am currently converting from V6 to V8.
Perfect candidate to test your software on.

Has the download link been shared yet?
The free demo version is
mattyjf01
Posts: 282
Joined: Wed Sep 04, 2019 8:41 pm

Re: VE V6 ECU LINKER

Post by mattyjf01 »

Like I've done with the VZ software I'm adapting it to ELM327 USB and Bluetooth

Here are ones that don't work out of the box
20220418_111803.jpg
The Best one I've found is the forscan with the high/low switch which can be easily modified to be CAN/SWCAN
20220418_111309.jpg
Swap pin 3 -> 1
Swap pin 11 -> 4 (I connected it to 4 and 5)
20220418_105333.jpg
20220418_105341.jpg
Swapped
20220418_110741.jpg
mattyjf01
Posts: 282
Joined: Wed Sep 04, 2019 8:41 pm

Re: VE V6 ECU LINKER

Post by mattyjf01 »

Home Workstation
Taking over the lounge room (The wife loves it) :lol:
20220418_114446.jpg
Post Reply