Delco OSE FlashTool V1.51
Re: Delco FlashTool V1.51
the first part around Exx has the VIN and bin type DMTY, which will be FF if it has been cleared. So yours still has the info in it, so you should be able to full flash the pcm and plug in with vats enabled and it should work. If that area was FF then you'd need vats off as it wouldn't contain the link info or you would flash it, then relink with tech2.
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Delco FlashTool V1.51
thanks mate
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Delco FlashTool V1.51
must of done something right runs same as allways woot now to see if i can finish off the trans LOL
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- krusty
- Posts: 570
- Joined: Wed Jan 27, 2010 9:45 pm
- cars: VY Calais guzzler, Toyota Corolla almost hybrid
- Location: Melbourne, VIC
Re: Delco FlashTool V1.51
Attempting to use the flash tool to tune a VS V8 with 531 manual pcm via your usb aldl connector
Do I need to do any wiring to the pcm to enable read as I cannot connect?
I HAVE A ds1245Y WITH vs v8 enhanced $A5 loaded and the car runs no worries. Just no comms between laptop and nv ram
Any help is appreciated
Do I need to do any wiring to the pcm to enable read as I cannot connect?
I HAVE A ds1245Y WITH vs v8 enhanced $A5 loaded and the car runs no worries. Just no comms between laptop and nv ram
Any help is appreciated
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco FlashTool V1.51
check that you have 12v's and ground properly at the ALDL plug, as for checking the data wire, not much you can do there (other than it working) but you can check that the connectors are all in the plug and such I guess.
so the flashtool isn't connecting to it I assume ?
what settings are you using in the config ?
so the flashtool isn't connecting to it I assume ?
what settings are you using in the config ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- krusty
- Posts: 570
- Joined: Wed Jan 27, 2010 9:45 pm
- cars: VY Calais guzzler, Toyota Corolla almost hybrid
- Location: Melbourne, VIC
Re: Delco FlashTool V1.51
I'll confirm pinouts are good now.Holden202T wrote:check that you have 12v's and ground properly at the ALDL plug, as for checking the data wire, not much you can do there (other than it working) but you can check that the connectors are all in the plug and such I guess.
so the flashtool isn't connecting to it I assume ?
what settings are you using in the config ?
These are the settings I'm using
- Attachments
-
- flash.png (24.69 KiB) Viewed 6277 times
Re: Delco FlashTool V1.51
531 is series 3, which is a VT pcm... try the VT settings.
- krusty
- Posts: 570
- Joined: Wed Jan 27, 2010 9:45 pm
- cars: VY Calais guzzler, Toyota Corolla almost hybrid
- Location: Melbourne, VIC
Re: Delco FlashTool V1.51
Good call mate. The VS bin only being 64k will still get looked up in the same place only anyways wouldn't it? I think the jumpers on the NVRAM dictate that and the Flash tool options don't accomodate for VTJayme wrote:531 is series 3, which is a VT pcm... try the VT settings.
I may be having a blond moment but not sure what else to try there
Pin outs are all good too btw
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Delco FlashTool V1.51
Try "VS V8 on Bench" and change to F5 for device ID, or "VS Eco or S/C on Bench". Without seeing the log from the flashtool its possibly the BCM not responding.
VS series 3 are 128k bins.
VS series 3 are 128k bins.
- krusty
- Posts: 570
- Joined: Wed Jan 27, 2010 9:45 pm
- cars: VY Calais guzzler, Toyota Corolla almost hybrid
- Location: Melbourne, VIC
Re: Delco FlashTool V1.51
My bad, yes 128k is rightVL400 wrote:Try "VS V8 on Bench" and change to F5 for device ID, or "VS Eco or S/C on Bench". Without seeing the log from the flashtool its possibly the BCM not responding.
VS series 3 are 128k bins.
Tried to connect flash as Ecotec bench and we're in business