WB O2 output

Information and discussion of EFI hardware and specifications
Post Reply
benk
Posts: 189
Joined: Mon Apr 12, 2010 12:58 pm
cars: VN V6 Commodore

WB O2 output

Post by benk »

have an issue with my WB O2 sensor doesn't seem to be reading correctly in Tunerpro.
I have a 14point7 kit installed and the readout is around 1 unit out to what Tunerpro is reading. Wanted to check output range on the Wideband and input in TP to make sure that they are the same. I can remember reading something about the settings a while ago but can't seem to find the post. Can find what the settings are on the wideband controler but not sure where to find them in TP
Top
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: WB O2 output

Post by The1 »

14point7 kits are 10-20 AFR usually, so calc you would use in tunerpro is ((20.00-10.00)/255*x)+10.00 if your using an enhanced port, if it's injector monitor line change the 255 to 60, depending on voltage you may need to change the 60 to between 50-60
Top
benk
Posts: 189
Joined: Mon Apr 12, 2010 12:58 pm
cars: VN V6 Commodore

Re: WB O2 output

Post by benk »

ok.... so where do I check/ change that in TP??
I'm using 12P on an 808 so the Pin I'm using is D8
Top
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: WB O2 output

Post by The1 »

Acquisition menu, edit definition, drop down values and find the wideband, conversion tab, hit set button to change the calc.
Top
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:
Contact VL400

Re: WB O2 output

Post by VL400 »

12P is different, there are two scalars to change and the ECU handles the calc for you - it should always be left as X/10. Set "VE Learn Params - WideBand 0v AFR" and "VE Learn Params - WideBand 5v AFR" to suit the wideband - so 0V to 10AFR and 5V to 20AFR with a 14point7 kit if that is what the output is set for (there should be instructions with the kit that specify the output).
Top
benk
Posts: 189
Joined: Mon Apr 12, 2010 12:58 pm
cars: VN V6 Commodore

Re: WB O2 output

Post by benk »

Changed the 0 and 5v setpoints and reads fine now :)
Top
User avatar
vlad01
Posts: 7794
Joined: Mon Oct 08, 2012 6:41 pm
cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive
Location: Kyneton, Vic

Re: WB O2 output

Post by vlad01 »

which WB is better in terms of quality and reliability?

the 14point7 or the LC-1 ?

I know the LC-1 has better feature that will be useful but is it worth the 95 bucks more?
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Top
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: WB O2 output

Post by The1 »

i thought it was only gauge or no gauge?
Top
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:
Contact Holden202T

Re: WB O2 output

Post by Holden202T »

LC-1 is wideband plus controller, gauge is extra, its the MTX-L that has the gauge as part of it ....

personally I haven't used anything other than the two above so can't comment on comparing, but I can't fault them either.
Top
vc81
Posts: 158
Joined: Tue Jan 01, 2013 7:32 pm
cars: vn v6

Re: WB O2 output

Post by vc81 »

benk wrote:have an issue with my WB O2 sensor doesn't seem to be reading correctly in Tunerpro.
I have a 14point7 kit installed and the readout is around 1 unit out to what Tunerpro is reading. Wanted to check output range on the Wideband and input in TP to make sure that they are the same. I can remember reading something about the settings a while ago but can't seem to find the post. Can find what the settings are on the wideband controler but not sure where to find them in TP
I have exactly the same problem but with a mtx-L. The wideband 0V & 5V scalars are set on 7.30 & 22.4 which I believe to be correct for the mtl=l. Any ideas why the mtx=l gauge readout is different to the TP dash readout?
Top
Post Reply

Return to “Hardware”