Injector Flow Testing Data

Information and discussion of EFI hardware and specifications
User avatar
Posts: 2566
Joined: Sun Mar 01, 2009 8:59 am
Location: North Coast, NSW

Re: Injector Flow Testing Data

Postby Jayme » Tue Sep 02, 2014 8:02 am

ooooooooo looks a lot more technical and complicated than the average flow bench :P

trying to figure out what all the boxes are for?? top one is the original flow bench controller? middle one I would say scope by the coax leads going in, but there is no display so I give up. bottom one is variable voltage power supply?

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Tue Sep 02, 2014 9:10 am

top one is a fluke 5 1/2 digit multimeter, middle one is a HP Frequency Generator, bottom one is a manson variable power supply.

I have another HP Freq Gen just not setup atm so i can feed both MAF and VSS in. Jimstim in front of the PSU and i have another cheap freq gen next to jimstim to feed in knock signal and another board to convert crank for cam pulse.

User avatar
Posts: 4983
Joined: Sun Mar 01, 2009 2:54 pm
Location: Perth, WA

Re: Injector Flow Testing Data

Postby VL400 » Tue Sep 02, 2014 11:34 am

:lol: I also thought it was the kitchen, was wondering how you got that past the boss!

Looks really trick, certainly the most complicated inj flow bench I have seen.

User avatar
Posts: 9500
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: Injector Flow Testing Data

Postby Holden202T » Tue Sep 02, 2014 12:22 pm

definitely very professional looking :)

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Tue Sep 02, 2014 9:35 pm

test run, holds pressure ok with a set of 42lb injectors, biggest i have atm. B10 is the fuel pressure. Will need to try higher pressure and see how it goes.
Attachments
flow bench run.jpg
flow bench run.jpg (136.09 KiB) Viewed 1637 times

Posts: 2440
Joined: Thu Apr 09, 2009 12:31 pm

Re: Injector Flow Testing Data

Postby immortality » Wed Sep 03, 2014 8:32 am

It is a very impressive set up with results to match :)

User avatar
Posts: 6099
Joined: Mon Oct 08, 2012 6:41 pm
Location: Kyneton, Vic

Re: Injector Flow Testing Data

Postby vlad01 » Wed Sep 03, 2014 11:21 am

nice and steady that.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.

User avatar
Posts: 2566
Joined: Sun Mar 01, 2009 8:59 am
Location: North Coast, NSW

Re: Injector Flow Testing Data

Postby Jayme » Wed Sep 03, 2014 12:03 pm

be interesting to see how the pump holds up to the ID1000's

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Wed Sep 03, 2014 12:56 pm

will be interesting, 044 wont handle them for sure but interesting to see what it can supply.

User avatar
Posts: 9500
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: Injector Flow Testing Data

Postby Holden202T » Wed Sep 03, 2014 10:06 pm

Hahaha I maxed an 044 with deka 80's so you'll definitely have issues, maybe you need two 044's like I have now!

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 3 guests