Injector Flow Testing Data

Information and discussion of EFI hardware and specifications
User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Thu Sep 04, 2014 12:00 am

yep no doubt it will, though so far i haven't had demand for much over 42lb, though really it's only the high DC and RPM tests that will test it, low stuff and calibration type runs wont be an issue. I am toying with purchasing a used HP Switching Control unit and setting up automated runs with the psu and pcm.

User avatar
Posts: 9500
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: Injector Flow Testing Data

Postby Holden202T » Thu Sep 04, 2014 7:50 am

you can also test only 4 injectors at a time to give you the capacity if needed!

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Thu Sep 04, 2014 8:56 am

sorry dont follow? i can run any number.

Posts: 152
Joined: Mon Jul 04, 2011 8:37 pm
Location: SOR, WA

Re: Injector Flow Testing Data

Postby Helical » Thu Sep 04, 2014 10:01 am

Less injectors less flow required, won't max out the pump, I think that's what he's getting at.

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Thu Sep 04, 2014 8:52 pm

yeh thought so.

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Sun Sep 07, 2014 10:36 pm

Did some testing on brand new Bosch 1000cc injectors from Jayme
Attachments
0280158117 1000cc.zip
(4.3 MiB) Downloaded 93 times

User avatar
Posts: 9500
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: Injector Flow Testing Data

Postby Holden202T » Mon Sep 08, 2014 10:11 am

definitely looks like more of a misty spray than the deka's direct stream hehe :)

User avatar
Posts: 6099
Joined: Mon Oct 08, 2012 6:41 pm
Location: Kyneton, Vic

Re: Injector Flow Testing Data

Postby vlad01 » Mon Sep 08, 2014 12:11 pm

nice action shots there.

Whats with the 0 dead times below 8V?
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Mon Sep 08, 2014 12:31 pm

no go, they need'd quiet a bit of time and even then very erratic. cranking usually doesn't go below 10v so shouldn't need it, but can put the default max in 3.89

User avatar
Posts: 6099
Joined: Mon Oct 08, 2012 6:41 pm
Location: Kyneton, Vic

Re: Injector Flow Testing Data

Postby vlad01 » Mon Sep 08, 2014 12:35 pm

oh ok.

So basically they don't operate properly below that voltage.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 2 guests