Injector Flow Testing Data
Re: Injector Flow Testing Data
hard to tell, but yeh if i get one spare ill cut the tip off.
42lb bosch 0280156127 20LB 901 20LB 960
42lb bosch 0280156127 20LB 901 20LB 960
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Injector Flow Testing Data
unscrew the metal cap so they say.the v6 sprintcar guys here started buying them up.then someone on the turbo page on FB said they flow 50 uncapped that would be correct 3x the flow for meth
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Injector Flow Testing Data
yeah except methanol is 2.3 times but yeah works out to be about 45-50lbs to be on the safe side.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Injector Flow Testing Data
so i just took the end off .its screwed on nice fine thread and sure enough the plate in the screw on tip with 4 holes is just sitting there and flicks out. you could tailor make any flow rate just by swapping in other discs from donor injectors with bigger holes
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: Injector Flow Testing Data
good to see, wonder if the tip is a restriction at all, or if even they get better atomization without having it all forced through a single hole, ill do some testing here when i get a chance.
- antus
- Site Admin
- Posts: 8253
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Injector Flow Testing Data
I would suspect its kinda ballpark, but may not be as consistant. Would be interesting to see before and after of a few.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: Injector Flow Testing Data
did you just get the tip off or the whole end housing? The one i have here to mess with the whole end housing spins in the end of the injector, ive tried holding in the middle with pliers so i can try and take the end tip off but dont have anything small enough that will hold it.
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Injector Flow Testing Data
i just grabbed the metal end cap with vicegrips and turned it while holding the injector in my hand lefty loosy .its lock tighted on and i had to screw it foward and back a couple of times to break the seal then it just unscrewed
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Injector Flow Testing Data
the whole shiney metal end comes off then the spreader is just sitting in there
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: Injector Flow Testing Data
i checked on two i have here and both just spin the whole barrel, to get the tip off id need something to grip the barrel. Ill prob just cut the tip on this one with hacksaw