LC-1 Wide band sensor

Information and discussion of EFI hardware and specifications
Charlescrown
Posts: 1831
Joined: Sat Aug 06, 2011 7:58 am
cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes
Location: Padstow NSW

Re: LC-1 Wide band sensor

Post by Charlescrown »

Is that a US website? Our dollar is worth around 74 cents.
Charlescrown
Posts: 1831
Joined: Sat Aug 06, 2011 7:58 am
cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes
Location: Padstow NSW

Re: LC-1 Wide band sensor

Post by Charlescrown »

Oh I think you mean they are both 4.2. Funny I have a LM2 and it takes the 4.2 and also a LC1 and it uses the 4.9. That's what I was going off.
MAGP
Posts: 665
Joined: Tue May 10, 2016 5:48 pm
cars: VC V8 sedan, VS V6 wagon, VT V8 Landcruiser.

Re: LC-1 Wide band sensor

Post by MAGP »

Charlescrown wrote:Is that a US website? Our dollar is worth around 74 cents.
????????
Charlescrown wrote:Oh I think you mean they are both 4.2.
Nope, I mean you need to check the manufacturers website to see what is required. The manufacturers says the LC-1 uses the 4.2. I never said anything about the 4.9, LM2 or anythign else.
Charlescrown wrote:Funny I have a LM2 and it takes the 4.2 and also a LC1 and it uses the 4.9. That's what I was going off.
:silent:
Charlescrown
Posts: 1831
Joined: Sat Aug 06, 2011 7:58 am
cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes
Location: Padstow NSW

Re: LC-1 Wide band sensor

Post by Charlescrown »

Sorry my mistake. If the LC1 uses the 4.2 then the first Holden number 12575904 should fit. I use one now for my LM2 after I ran over the original one supplied by Innovate the only difference is the cable was a little shorter.
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: LC-1 Wide band sensor

Post by Holden202T »

I think the LC2 uses the 4.9 ? I have a 4.9 kit for my MTX-L haven't used it yet though.
VK_3800
Posts: 526
Joined: Sun Jul 04, 2010 3:15 pm
cars: SS Torana
Location: NZ

Re: LC-1 Wide band sensor

Post by VK_3800 »

My LC-1 uses a 4.2, they did revise it at some stage but not sure if it was renamed or not
Charlescrown
Posts: 1831
Joined: Sat Aug 06, 2011 7:58 am
cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes
Location: Padstow NSW

Re: LC-1 Wide band sensor

Post by Charlescrown »

I know my LM2 can be upgraded to the 4.9 with a software and cable change but if so many manufacturers use the 4.2 and they last I don't see the need for the upgrade.
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: LC-1 Wide band sensor

Post by Holden202T »

Yeah my MTX-L was the same upgrade.
Post Reply