Speeduino ECU
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Speeduino ECU
Yeah I might be keen on a play with 1 depending on cost to get setup
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: Speeduino ECU
I'd like to know how it handles sensor failures?
Does it have a "Limp Home" mode like a factory ECU?
Thanks.
Chuff
Does it have a "Limp Home" mode like a factory ECU?
Thanks.
Chuff
˙ʎɐqǝ ɟɟo pɹɐoqʎǝʞ ǝsǝuıɥɔ ɐ ƃuıʎnq ɹoɟ ʇɥƃıɹ ǝɯ sǝʌɹǝs
-
- Posts: 5
- Joined: Wed Jul 29, 2009 8:20 pm
- cars: Vn Commodore
Subaru MY98 WRX
Hyundai Excel RWD V6 Turbo
Toyota Tarago
Subaru Sherpa
Kia Rio
Re: Speeduino ECU
I have a few boards left, Id only sell them with components fitted and you can assemble the rest (main connector/IAC/ etc as the BOM for parts isnt correct and board need a slight mod for the bypass.
Id have to work out a price.
the through hole boards work as a plug in shield onto a Arduino mega2560.
I had Josh add a bypass pin, that activated at a set rpm (user setting) so the factory DFI or 304 ignition module can be used.
Input signal is received from DFI/Ignition module.
Has Stepper motor controller to run the IAC (and newest firmware can control idle closed loop)
Has Header for Bluetooth module (HC-05/06)
TPS, Map, CLT, IAT, O2 inputs
2 injector, 1 ignition, Bypass, Thermofan, fuel pump output
Trigger input is optic isolated.
can't see why it wouldn't fit in a standard case board is 10cm x 10cm, if anything it may be hight.
never tried a sensor error yet. i know the CLT and IAT have a default setting.
Id have to work out a price.
the through hole boards work as a plug in shield onto a Arduino mega2560.
I had Josh add a bypass pin, that activated at a set rpm (user setting) so the factory DFI or 304 ignition module can be used.
Input signal is received from DFI/Ignition module.
Has Stepper motor controller to run the IAC (and newest firmware can control idle closed loop)
Has Header for Bluetooth module (HC-05/06)
TPS, Map, CLT, IAT, O2 inputs
2 injector, 1 ignition, Bypass, Thermofan, fuel pump output
Trigger input is optic isolated.
can't see why it wouldn't fit in a standard case board is 10cm x 10cm, if anything it may be hight.
never tried a sensor error yet. i know the CLT and IAT have a default setting.
- jenko
- Posts: 450
- Joined: Wed Jan 29, 2014 3:43 pm
- cars: hilux v6
jaguar v12
mitsubishi lancer
fj cruiser
sv 21 camry wagon - Location: Pine mountain .vic
- Contact:
Re: Speeduino ECU
Also does it have the map sensor onboard or have you changed it to use the vehicle one
-
- Posts: 5
- Joined: Wed Jul 29, 2009 8:20 pm
- cars: Vn Commodore
Subaru MY98 WRX
Hyundai Excel RWD V6 Turbo
Toyota Tarago
Subaru Sherpa
Kia Rio
Re: Speeduino ECU
It uses the factory one
Re: Speeduino ECU
how well do the components handle heat? cabin temps can get quite warm.
Re: Speeduino ECU
Hi all,
Somebody have experience with MS?
I have plan to upgrade my delco ECU (OBD 1, Opel engine) to MS?
Cheers
Somebody have experience with MS?
I have plan to upgrade my delco ECU (OBD 1, Opel engine) to MS?
Cheers
- vlad01
- Posts: 7801
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Speeduino ECU
I havn't got experience but I did a fair bit of research on MS as thats what I was planing to use, but I stuck with the original delco as it was far more capable than the early MS versions, cheaper, and easier to tune.
What is the specs of you car, engine and efi setup mainly is what I am after.
What is the specs of you car, engine and efi setup mainly is what I am after.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Speeduino ECU
My car used C22NE opel/Holden engine MPFI n run with delco multec M ECU... I think this engine used in Holden rodeo TF too... Really need the base tune to run MS in my engine....