Schematics for 1227165 (1227808 with additional IC U2)

Information and discussion of EFI hardware and specifications
Post Reply
bf6379
Posts: 32
Joined: Wed Jun 20, 2018 11:38 am
cars: HZ Kingswood 304
VS Ute 304
VE SV6 3.6 SIDI
VF SS 6.2

Schematics for 1227165 (1227808 with additional IC U2)

Post by bf6379 »

Sheet 1 - Processor
Sheet 1 - Processor
Sheet 2 - Inputs
Sheet 2 - Inputs
Sheet 3 - Outputs
Sheet 3 - Outputs
Sheet 4 - Ignition and Injectors
Sheet 4 - Ignition and Injectors
Sheet 5 - Connectors
Sheet 5 - Connectors
Sheet 6 - Power Supply
Sheet 6 - Power Supply
User avatar
antus
Site Admin
Posts: 8237
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: Schematics for 1227165 (1227808 with additional IC U2)

Post by antus »

Thanks for that. I'll make it a sticky.

For anyone looking for simiar content for other ECMs around the same era there is also a mirror of the original source (Ludis' site) with schematics and other content which we have mirrored here https://pcmhacking.net/ludis/
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
pman92
Posts: 464
Joined: Thu May 03, 2012 10:50 pm
cars: HZ One Tonner
VE Ute
Location: Castlemaine, Vic

Re: Schematics for 1227165 (1227808 with additional IC U2)

Post by pman92 »

Awesome. I know you've also got the memcal page mirrored here. What else is mirrored here, or is that it?
VR-VY Holden BCM Simulator: View Post
MrModule.com.au
User avatar
antus
Site Admin
Posts: 8237
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: Schematics for 1227165 (1227808 with additional IC U2)

Post by antus »

https://pcmhacking.net/memcals.html
Thats the only two. They both seemed like great information we couldnt afford to loose.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
User avatar
charlay86
Posts: 584
Joined: Thu Sep 17, 2009 2:00 pm
cars: VT S1 SS (L67)
Location: Perth, WA

Re: Schematics for 1227165 (1227808 with additional IC U2)

Post by charlay86 »

For those of you who can't get simulated narrowband O2 signal from a wideband lambda controller to work with these (and later) ECMs:
If you look at the inputs schematic and take note of the O2 sensor amplifier, you will note that it has two inputs pins.
O2HI - obvious, the narrowband signal comes in here.
O2LO - perhaps less obvious, it needs to connect directly to the signal ground PIN on the wideband controller.
Ideally you would splice the wideband controller signal ground wire (goes to engine block ) and O2LO wire (to ECM) as close as possible to the wideband controller, ideally in the connector.
Post Reply