VS getrag wiring
VS getrag wiring
I am doing a getrag vs conversion to my t5 vr.I have all the original wiring on the newer engine so the computer wiring will be ok but the low bcm that I have will need a few mods to get it to fly using my old vr body loom...just wondered if anybody had the pinouts/wiring diagram for the vs bcm
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: VS getrag wiring
yeah I did find them a wqhile back just with google searches ... I think they were on the justcommodore forums from memory, they weren't the best quality scans but they gave the information I needed.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- TdracerTd
- Posts: 488
- Joined: Mon Aug 19, 2013 10:39 pm
- cars: Td Gemini coupe (race car WIP)
Holden VE SS ute (tow car/daily)
Vp commodore V6 (race car, s/c, e85, intercooled)
Jeep Grand Cherokee Overland (mrs car, family bus)
My12 subaru STi (Weekend warrior/Toy)
1972 LJ torana GTR (my Dad's car)
Mitsubishi Evo IX
Re: VS getrag wiring
What's the advantage of going to a getrag over T5?
Re: VS getrag wiring
Not sure but they carried over to later vt/x models but the dual mass flywheel has some downsides and the donut style coupling is a little foreign to me but it came with the vs engine I bought with all the wiring /computer pedals bcm etc so as a upgrade ill go with it and get it going with some wiring help from this forum and Ill give you my opinion but my old t5 is there if it doesnt work out.TdracerTd wrote:What's the advantage of going to a getrag over T5?
bit different tailshaft setup from a t5 and the open style 2 wire speed sensor
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: VS getrag wiring
from what i've experienced with the rubber uni joint they work fine, I did over 250,000kms in my VZ ute, a lot of it towing car on trailer and I never had an issue with it!!
I'd love to see a camera under a car on take off though to see what it does to it
I'd love to see a camera under a car on take off though to see what it does to it
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: VS getrag wiring
The Getrag is supposed to be a more refined transmission unfortunately it's no stronger than the T5. It has slightly different ratios too.
No problems with the coupling, they are standard on all later model Commodores.
No problems with the coupling, they are standard on all later model Commodores.
-
- Posts: 149
- Joined: Wed Oct 31, 2012 6:59 pm
- cars: VY commodore supercharged V6
- Location: Sydney
Re: VS getrag wiring
I killed the rubber coupling as with everything if you abuse it they fail