Ecotec Waterpump Pulley with no Centre Hub
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Ecotec Waterpump Pulley with no Centre Hub
I'm sure i've got more than one of them sitting at home somewhere!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- vlad01
- Posts: 7801
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Ecotec Waterpump Pulley with no Centre Hub
The buick ones hub centric, and the ecotec ones locate on the dimples. If you hole saw it, its wont center right and vibrate the bearings to shit in the pump.
There should be literally millions of these at the wreckers.
There should be literally millions of these at the wreckers.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
- vlad01
- Posts: 7801
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Ecotec Waterpump Pulley with no Centre Hub
Dude! just get this. They are on clearance and normally sell $130
https://billetracecraft.com.au/product/ ... dard-size/
https://billetracecraft.com.au/product/ ... dard-size/
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Ecotec Waterpump Pulley with no Centre Hub
yeh i did notice them, So maybe cutting hole wont work. I have contacted 3 wreckers here and none have seen them :/ That link looks great but out of stock.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Ecotec Waterpump Pulley with no Centre Hub
if you have no luck, PM or email me and i'll see what I got when I get home!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Ecotec Waterpump Pulley with no Centre Hub
none so far, happy to pay if anyone has one they can part with.
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: Ecotec Waterpump Pulley with no Centre Hub
I found one, It's yours if you want it. I'm heading into the town centre tomorrow so can swing past the mail centre to post it.
They are easy enough to centre, bolt it on and spin it by hand, then adjust to suit. Not hardvlad01 wrote:The buick ones hub centric, and the ecotec ones locate on the dimples. If you hole saw it, its wont center right and vibrate the bearings to shit in the pump.
There should be literally millions of these at the wreckers.
-
- Posts: 288
- Joined: Wed Jul 01, 2009 7:18 pm
- cars: VY V6 Commodore ute.
VS V6 Commo sedan.
VT V6 powered 4x4 Hilux ute.
Re: Ecotec Waterpump Pulley with no Centre Hub
Know anyone with a lathe ? They could take the centre out possibly for you.
- vlad01
- Posts: 7801
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Ecotec Waterpump Pulley with no Centre Hub
I had a look, I don't have any spares.
But I did get a good look at all the pumps to see what brand.
VP S had its changed before, no name pump, both VR and the new engine have GMB with no japan markings, old VP engine has a japan one, VT? engine has still factory genuine GM one (JDMP ? brand?) has GM 125xxxx... number on it, never been removed and is as shipped from the US.
But I did get a good look at all the pumps to see what brand.
VP S had its changed before, no name pump, both VR and the new engine have GMB with no japan markings, old VP engine has a japan one, VT? engine has still factory genuine GM one (JDMP ? brand?) has GM 125xxxx... number on it, never been removed and is as shipped from the US.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.