Got ya ! Better than a cable lolvlad01 wrote:As long as the cylinder ratio and pipe diameters is big enough they do feel and operate awesome.
T5 - Concentric Release Bearing
Re: T5 - Concentric Release Bearing
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: T5 - Concentric Release Bearing
yours isn't though. Yours feels slow and sloshy like a 1976 Dodge truck . I reckon the pipe is too small.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: T5 - Concentric Release Bearing
I've felt some good and some bad. A lot of the new cars are ok, but retrofits on many I have driven feel shithouse. I do still prefer cable as I'm used to T5 which have awesome feeling cable setup from factory, I'd hate to ruin that.immortality wrote:I've experienced the exact opposite, very vague hydraulic clutches, much preferred the old cable clutch has you can feel what is happening.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: T5 - Concentric Release Bearing
?? You havnt driven mine ! Lolvlad01 wrote:yours isn't though. Yours feels slow and sloshy like a 1976 Dodge truck . I reckon the pipe is too small.
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: T5 - Concentric Release Bearing
no, but i did try the clutch the few times I sat in it. don't you remember me complaining about it? lol, and you were ranting how good it was.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
- Posts: 288
- Joined: Wed Jul 01, 2009 7:18 pm
- cars: VY V6 Commodore ute.
VS V6 Commo sedan.
VT V6 powered 4x4 Hilux ute.
Re: T5 - Concentric Release Bearing
It is one of my many projects that I have not gone far with as yet..psyolent wrote:Hi
Anyone fitted one of these to a T5 and done away with the cable clutch configuration on the earliers?
Wanting to fit a T5 to a VT ; and keep the hydraulics and not have the cable.
Just digging
I have bought two all steel input shaft bearing retainer housings (GM V8), which I was going to some how either adapt a CSC from the GMH T56 onto the front, or have a complete new one machined up that the CSC can bolt on to.
The V6 GMH T5 uses the Alloy bearing retainer cap with pressed steel tube so that seems a bit flexible to me, hence I sourced a couple of all steel ones.
With the GMH Input (main shaft) being so long the adapter will also be quite lengthy it seems. Got a couple of GMH T56 CSC units & two billets of large diameter alloy plus the steel input shaft housings. Just need a lot more time & the drive to get it sussed out.
The units Mal Woods uses in the link have me wonder how they set them up as I imagine the need to be solid mounted to something or need to push off a backing plate. Or maybe they are only suitable for the shorter shaft V8 T5's ?
Cheers
-
- Posts: 288
- Joined: Wed Jul 01, 2009 7:18 pm
- cars: VY V6 Commodore ute.
VS V6 Commo sedan.
VT V6 powered 4x4 Hilux ute.
Re: T5 - Concentric Release Bearing
I agree the cable operated T5 in my VS V6 is a very good feel & surprisingly light. Part of the reason I am going to try the twin plate clutch using the cable operation before getting into the hydraulic conversion.vlad01 wrote:I've felt some good and some bad. A lot of the new cars are ok, but retrofits on many I have driven feel shithouse. I do still prefer cable as I'm used to T5 which have awesome feeling cable setup from factory, I'd hate to ruin that.immortality wrote:I've experienced the exact opposite, very vague hydraulic clutches, much preferred the old cable clutch has you can feel what is happening.
Cheers
Re: T5 - Concentric Release Bearing
You always complain lol, you can't judge it until you drive it !vlad01 wrote:no, but i did try the clutch the few times I sat in it. don't you remember me complaining about it? lol, and you were ranting how good it was.
Re: T5 - Concentric Release Bearing
I like the Tilton ones (stupid pricey but you never regret it), have used on Aussie 4 speed, Muncie and now TKO600. Threaded adjustment rather than shims means you don't have to pull the gearbox if you measure wrong!
Issues with poor feel are exactly the same as cable or pushrod clutch - you need to set it up right with the right lever ratio, the fluid still gives a mechanical connection. Ditching the fork is great for uniform feel and one less point of failure in the chain. If your master cylinder is in the ball park in terms of bore and stroke then you will be able to use it, often you can tweak the travel at the pedal to get it just right.
Going to go a bit cheaper on the ute with one of those Howe units and an LT1 T56 (very short bell housing, originally had a pull clutch like the HSV VR-VT strokers). If I get around to it.
Issues with poor feel are exactly the same as cable or pushrod clutch - you need to set it up right with the right lever ratio, the fluid still gives a mechanical connection. Ditching the fork is great for uniform feel and one less point of failure in the chain. If your master cylinder is in the ball park in terms of bore and stroke then you will be able to use it, often you can tweak the travel at the pedal to get it just right.
Going to go a bit cheaper on the ute with one of those Howe units and an LT1 T56 (very short bell housing, originally had a pull clutch like the HSV VR-VT strokers). If I get around to it.
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: T5 - Concentric Release Bearing
You can pick up used 3 plate Tilton clutches on ebay, just need to get new plates to suit your box.