Seed/Key Osid and Vin retrieval via Elm
-
- Posts: 51
- Joined: Thu Feb 07, 2013 1:49 pm
- cars: 2002 Camaro
2008 Pontiac G8
Re: Seed/Key Osid and Vin retrieval via Elm
Tre what actual elm did you use and how did you set it up? I've tried this program with two different elm cables and no workie for me
Re: Seed/Key Osid and Vin retrieval via Elm
I also have several Elm cables still does not work.
I loaded a 2001 Cavalier L4 2.4 tune into a pcm tried again still did not work.
I loaded a 2001 Cavalier L4 2.4 tune into a pcm tried again still did not work.
Re: Seed/Key Osid and Vin retrieval via Elm
has anyone been successful in using the tool on ls1 ecu's? im having trouble connecting the laptop to read the vin etc.
- Tre-Cool
- Posts: 287
- Joined: Tue Oct 16, 2012 12:17 pm
- cars: VY SS UTE, VX Drag Car
- Location: Perth
- Contact:
Re: Seed/Key Osid and Vin retrieval via Elm
mine is just a run of the mill 1.3a elm cable, but I believe it's a genuine chipset, not a clone.
http://www.webpg.net/products/obd2usb.asp
that's what mine is. however im also talking to the ecu via bench harness.
http://www.webpg.net/products/obd2usb.asp
that's what mine is. however im also talking to the ecu via bench harness.
Re: Seed/Key Osid and Vin retrieval via Elm
so I have my new cable, same as above, but is a elm327 v1.4b
I keep getting CAN ERROR, and when commanding at sh 6c 10 f1 I get ok nothing else....
can anyone shed some light as to where ive gone wrong? thanks mat
I keep getting CAN ERROR, and when commanding at sh 6c 10 f1 I get ok nothing else....
can anyone shed some light as to where ive gone wrong? thanks mat
-
- Posts: 51
- Joined: Thu Feb 07, 2013 1:49 pm
- cars: 2002 Camaro
2008 Pontiac G8
Re: Seed/Key Osid and Vin retrieval via Elm
Tre-Cool wrote:mine is just a run of the mill 1.3a elm cable, but I believe it's a genuine chipset, not a clone.
http://www.webpg.net/products/obd2usb.asp
that's what mine is. however im also talking to the ecu via bench harness.
I bought this cable and it the program worked thanks!
Re: Seed/Key Osid and Vin retrieval via Elm
$110, Geeeeeeeeeeeeeeez.roughneck427 wrote:Tre-Cool wrote:mine is just a run of the mill 1.3a elm cable, but I believe it's a genuine chipset, not a clone.
http://www.webpg.net/products/obd2usb.asp
that's what mine is. however im also talking to the ecu via bench harness.
I bought this cable and it the program worked thanks!
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: Seed/Key Osid and Vin retrieval via Elm
Almost any elm 327 will work with this program if you set it up correctly.
Normally all you need to do is get elm to boot up running 9600 baud.(Its covered in elm datasheet)
Then using a terminal send command ATL1.
Normally all you need to do is get elm to boot up running 9600 baud.(Its covered in elm datasheet)
Then using a terminal send command ATL1.
Re: Seed/Key Osid and Vin retrieval via Elm
Not sure how this seed/key application initializes its connection to the ELM. But, logically, you would have thought it would connect at the default baud rate 38400.
Guess the ELMs may have been different back in 2010 though.
Guess the ELMs may have been different back in 2010 though.
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: Seed/Key Osid and Vin retrieval via Elm
Yeah a lot of the early elm versions ran the slower baud rate ,that is why people have been having success with older ones , and it must of been what planethax had when he wrote it.