GitHub repo for XDFs
-
- Posts: 397
- Joined: Wed Jul 05, 2017 8:30 am
- cars: 2001 Pontiac Grand AM SE
LD9 2.4l I4, 4T40E
2005 Chevrolet Venture
LA1 3400 V6, 4T65E - Location: North TX, USA
Re: GitHub repo for XDFs
Hi all,
With all the discussion of the various PCMs used, I thought this info might help:
https://www.lsenginediy.com/comparing-g ... ntrollers/
http://www.chevythunder.com/LS1%20compo ... tification
https://www.chevythunder.com/gen_iv_ecm ... cation.htm
Hope this helps.
Mike
With all the discussion of the various PCMs used, I thought this info might help:
https://www.lsenginediy.com/comparing-g ... ntrollers/
http://www.chevythunder.com/LS1%20compo ... tification
https://www.chevythunder.com/gen_iv_ecm ... cation.htm
Hope this helps.
Mike
- DavidBraley
- Posts: 172
- Joined: Thu Jun 07, 2018 8:15 am
- cars: 1948 GMC
- Location: Fort Collins, Colorado
Re: GitHub repo for XDFs
NSFW,
I have a 2003 P59 PCM here with service #12576106, hardware #12570558 (drive by cable) that has the Intel AB28F800 flash chip in it. PCM Hammer will not read it. The BDM can read it, but there is no proper BDM config file (.xml) for writing to it. I'm happy to send it to you if it helps.
It's my understanding (I'm not 100% sure on this) that the 1 meg Intel chips only show up in the 2003 P59's.
There is another 2003 P59 with service #12581565, hardware #12575502 (drive by cable) that I read somewhere it has the Intel chip as well, but I don't physically have one. It's in my research notes though.
Let me know if you want the PCM I mention at the top of this message. I've completely disassembled it and deep cleaned it before re-assembly. I do not think it's dead either. The BDM will read it. Just can't write to it without a proper config file.
I have a 2003 P59 PCM here with service #12576106, hardware #12570558 (drive by cable) that has the Intel AB28F800 flash chip in it. PCM Hammer will not read it. The BDM can read it, but there is no proper BDM config file (.xml) for writing to it. I'm happy to send it to you if it helps.
It's my understanding (I'm not 100% sure on this) that the 1 meg Intel chips only show up in the 2003 P59's.
There is another 2003 P59 with service #12581565, hardware #12575502 (drive by cable) that I read somewhere it has the Intel chip as well, but I don't physically have one. It's in my research notes though.
Let me know if you want the PCM I mention at the top of this message. I've completely disassembled it and deep cleaned it before re-assembly. I do not think it's dead either. The BDM will read it. Just can't write to it without a proper config file.
-David
I'm a machinist... because engineers need heroes too.
I'm a machinist... because engineers need heroes too.
Re: GitHub repo for XDFs
Peeked into another Os, this time 12579405, an Os from a 1m Intel chipped unit.Gampy wrote:I cannot imagine (don't know for sure) that an OS from a Intel Flash unit will work on a unit that has AMD Flash ...
And as expected no Amd code as it is prior to the appearance of the Amd chips.
That list is incomplete, erroneous and in my opinion woefully lacking in detail.ShorTuning wrote:I literally just gave you that information above with all the hardware and service numbers. Green means it has IAC/AC hardware. Unfortunately the hardware/service numbers are not stored in the bin file either so unless you can verify the PCM is virgin you pull tune files from you'll not have that information.
The Hardware Number is embedded in the bin, the Service Number is not.
The following is whats easy to glean from a bin that describes it:
- Hardware Number
- Operating System Number (OsID)
- Broadcast Code
- Calibration Number
- System Calibration Number
- Engine Calibration Number
- Engine Diagnostics Number
- Transmission Calibration Number
- Transmission Diagnostics Number
- Fuel System Calibration Number
- Speedometer Calibration Number
- Serial Number
- Vehicle Identification Number
Personally, If I do not know the information about a bin or even wonder about it's accuracy, I do not want it!
What I am interested in is purely Manufacture originals ... I have no desires to be involved in a repository of "Tunes" by every Tom Dick and Harry tweeking fuel trims et al a point or two and calling it their tune.
I can confirm that hardware number does in fact describe a 1m Intel chipped unit.DavidBraley wrote:There is another 2003 P59 with service #12581565, hardware #12575502 (drive by cable) that I read somewhere it has the Intel chip as well, but I don't physically have one. It's in my research notes though.
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
- ShorTuning
- Posts: 55
- Joined: Thu Dec 13, 2018 4:42 pm
- cars: 2002 Camaro
2002 Formula - Location: On the Dyno
- Contact:
Re: GitHub repo for XDFs
Yes you are correct. I have flashed all different tune files in all different P59's and not had any issues. The PCM listed above by DavidBraley I have not added to my list. I actually ran across one and hadn't had a chance to mess around with it to see what it did and didn't have.NSFW wrote:Dude I wrote most of this software and I'm not entirely clear on this stuff.ShorTuning wrote:I would like to think that people that would be using this information would have enough knowledge to know what file will work with what. Especially they should know what hardware they have and what capabilities it has.
Based on that chart it sounds like you're saying there's effectively 3 kinds of hardware that people need to be aware of:
1) P01 - all are usable with DBW or DBC
2) P59 without IAC - usable only for DBW
3) P59 with IAC - usable for DBW or DBC
Related question - do you know whether there's a hardware number that indicates a P59 with an Intel flash chip? I'd like to experiment on one of those before I take another shot at AMD, but I'm not sure how to identify one without opening it up.
- ShorTuning
- Posts: 55
- Joined: Thu Dec 13, 2018 4:42 pm
- cars: 2002 Camaro
2002 Formula - Location: On the Dyno
- Contact:
Re: GitHub repo for XDFs
The list is basic because that's all it needs to be. I know all of the information you listed is in the binary. If that is information you need listed out for a binary then more power to ya. It'll be a paragraph long file name lol.Gampy wrote:That list is incomplete, erroneous and in my opinion woefully lacking in detail.ShorTuning wrote:I literally just gave you that information above with all the hardware and service numbers. Green means it has IAC/AC hardware. Unfortunately the hardware/service numbers are not stored in the bin file either so unless you can verify the PCM is virgin you pull tune files from you'll not have that information.
The Hardware Number is embedded in the bin, the Service Number is not.
The following is whats easy to glean from a bin that describes it:I do have some ideas for some other bits, just haven't set down to it yet.
- Hardware Number
- Operating System Number (OsID)
- Broadcast Code
- Calibration Number
- System Calibration Number
- Engine Calibration Number
- Engine Diagnostics Number
- Transmission Calibration Number
- Transmission Diagnostics Number
- Fuel System Calibration Number
- Speedometer Calibration Number
- Serial Number
- Vehicle Identification Number
Personally, If I do not know the information about a bin or even wonder about it's accuracy, I do not want it!
What I am interested in is purely Manufacture originals ... I have no desires to be involved in a repository of "Tunes" by every Tom Dick and Harry tweeking fuel trims et al a point or two and calling it their tune.
-
- Posts: 397
- Joined: Wed Jul 05, 2017 8:30 am
- cars: 2001 Pontiac Grand AM SE
LD9 2.4l I4, 4T40E
2005 Chevrolet Venture
LA1 3400 V6, 4T65E - Location: North TX, USA
Re: GitHub repo for XDFs
Hi all,
Can someone tell me if the XDF for a given OS, such as '2088, will work for BOTH the V6 AND the V8 Vortec engines!
I have 2 '0411 PCM's out of V6 S/T SUV applications.
Thanks,
Mike
Can someone tell me if the XDF for a given OS, such as '2088, will work for BOTH the V6 AND the V8 Vortec engines!
I have 2 '0411 PCM's out of V6 S/T SUV applications.
Thanks,
Mike
- antus
- Site Admin
- Posts: 8253
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: GitHub repo for XDFs
It'll work for the any bin with the operating system id (OSID) 12202088. V6 and V8 isnt relevant to the OSID.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 397
- Joined: Wed Jul 05, 2017 8:30 am
- cars: 2001 Pontiac Grand AM SE
LD9 2.4l I4, 4T40E
2005 Chevrolet Venture
LA1 3400 V6, 4T65E - Location: North TX, USA
Re: GitHub repo for XDFs
Thanks Antus.
That's what I thought, but wanted to be sure.
Mike
That's what I thought, but wanted to be sure.
Mike
Re: GitHub repo for XDFs
So you have flashed OsID 12579405 on one of the following Hardware ID's, No issues, meaning the Os was happy??ShorTuning wrote:I have flashed all different tune files in all different P59's and not had any issues.
12583659
12589161
12589162
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
- antus
- Site Admin
- Posts: 8253
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: GitHub repo for XDFs
A good test would be something like a vin change. The flash tool kernel should handle both chips at os write time, typically, but the question is if an intel os can update the paramater block on an amd flash chip with the factory reflash code when it needs too.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396