V6 ability for pcm hammer.
- antus
- Site Admin
- Posts: 8239
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: V6 ability for pcm hammer.
My PCM turned out to be DOA Ive ordered another but back to waiting...
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: V6 ability for pcm hammer.
they refund it or you get ripped off
- antus
- Site Admin
- Posts: 8239
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: V6 ability for pcm hammer.
Not sure, it could have been my P01/P59 loom that damaged it, I didnt realise when I first hooked it up that I had a non-standard pin used for B+ that worked fine on the other pcms, but is used for something else on the p04. Going to give them the benefit of the doubt. International shipping from the US is a killer (more than the PCMs)
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: V6 ability for pcm hammer.
yeah my test harness uses 18,19 for power 59 for data and 60 for ground
its good for p01/p59 and p04
its good for p01/p59 and p04
- DavidBraley
- Posts: 172
- Joined: Thu Jun 07, 2018 8:15 am
- cars: 1948 GMC
- Location: Fort Collins, Colorado
Re: V6 ability for pcm hammer.
My bench harness:
Pin 19, Switched Battery (ignition)
Pin 20, 12V Battery
Pin 58, Data
Pin 60, Ground
12v is fused.
https://github.com/LegacyNsfw/PcmHacks/ ... h-Flashing
I'll check the V6 wiring diagrams before I use it...
Pin 19, Switched Battery (ignition)
Pin 20, 12V Battery
Pin 58, Data
Pin 60, Ground
12v is fused.
https://github.com/LegacyNsfw/PcmHacks/ ... h-Flashing
I'll check the V6 wiring diagrams before I use it...
-David
I'm a machinist... because engineers need heroes too.
I'm a machinist... because engineers need heroes too.
Re: V6 ability for pcm hammer.
Same pinout I have, havent tried a P04 though.Vampyre wrote:yeah my test harness uses 18,19 for power 59 for data and 60 for ground
its good for p01/p59 and p04
Is there a few part numbers for the _04 that we can search/look for? Happy pickup one also.
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
- antus
- Site Admin
- Posts: 8239
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: V6 ability for pcm hammer.
That is the standard pinouts and is correct. I built my desk loom way back, probably 8 years ago, I just expected it to work since its worked all this time on p01/p59. Its not an ongoing problem, just the kind of thing that burns you every so often doing this type of stuff.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: V6 ability for pcm hammer.
I bench flash tunes for swaps all the time so it gets almost daily use, its good for any pcm that has a blue connector any 0411 look alike pcm
-
- Posts: 397
- Joined: Wed Jul 05, 2017 8:30 am
- cars: 2001 Pontiac Grand AM SE
LD9 2.4l I4, 4T40E
2005 Chevrolet Venture
LA1 3400 V6, 4T65E - Location: North TX, USA
Re: V6 ability for pcm hammer.
Hi all,Tazzi wrote:Same pinout I have, havent tried a P04 though.Vampyre wrote:yeah my test harness uses 18,19 for power 59 for data and 60 for ground
its good for p01/p59 and p04
Is there a few part numbers for the _04 that we can search/look for? Happy pickup one also.
Tazzi, both the 2004 Olds Alero I had, and the 2005 Chevy Venture that I have, use the LA1 3400 V6. They both use the same PCM: I am sure there are others, but these two I know are used.
Mike
Re: V6 ability for pcm hammer.
Thanks Mike!
Just bought one now (https://www.ebay.com/itm/184108101526)
Come with some connectors too if anyone needs some here in Aus.
Just bought one now (https://www.ebay.com/itm/184108101526)
Come with some connectors too if anyone needs some here in Aus.
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726