PCM Hammer Release 014
Re: PCM Hammer Release 014
Some cars get a ton of errors, like mine (C5 corvette). Although write seems to be OK, Read is just tons of errors/interruptions.
Re: PCM Hammer Release 014
GeoNV,
Thank you!
You might want to juice up the battery voltage a bit ...
FYI, A debug log has everything the results log has plus more, so a debug log is a better log to post.
That log has some weird things going on in it ...
If you're going to do either a "Write OS, Callibration & Boot" or "Write Full Flash (Clone)" (i.e. OS swap),
1. Pay close attention to the kernel upload ... if it has errors (retries), question it!
2. ALWAYS do a Test Write, if it has errors (retries), question it!
Otherwise it's pretty darn safe, a failed "Write Calibration" is most likely recoverable.
Thank you!
You might want to juice up the battery voltage a bit ...
FYI, A debug log has everything the results log has plus more, so a debug log is a better log to post.
That log has some weird things going on in it ...
No, it does not say not to do it in vehicle anywhere ... It is perfectly fine to do in vehicle ... However, it is safer on the bench where there is less likely hood of external interference.[06:17:01:452] Address % Done Time Remaining
[06:17:02:484] 0x000000 0% Measuring read speed...
[06:17:04:532] Elm ID:
[06:17:04:547] 0x000400 0% Measuring read speed...
[06:17:05:610] 0x000800 0% Measuring read speed...
[06:17:06:767] 0x000C00 0% Measuring read speed...
[06:17:07:829] 0x001000 0% Measuring read speed...
[06:17:08:908] 0x001400 0% Measuring read speed...
[06:17:09:986] 0x001800 0% Measuring read speed...
[06:17:11:190] 0x001C00 0% Measuring read speed...
[06:17:12:237] 0x002000 0% 22:41
[06:17:13:284] 0x002400 0% 22:07
[06:17:14:331] 0x002800 0% 21:41
[06:17:15:769] All Pro ID:
[06:17:15:784] 0x002C00 1% 21:54
[06:17:16:847] 0x003000 1% 21:33
[06:17:17:941] 0x003400 1% 21:18
[06:17:19:051] 0x003800 1% 21:05
[06:17:20:176] 0x003C00 1% 20:55
[06:17:21:286] 0x004000 1% 20:46
[06:17:22:395] 0x004400 1% 20:37
[06:17:23:458] 0x004800 1% 20:27
[06:17:24:584] 0x004C00 1% 20:20
[06:17:25:678] 0x005000 1% 20:13
[06:17:27:007] All Pro self test result:
[06:17:27:023] 0x005400 2% 20:18
[06:17:28:086] 0x005800 2% 20:11
[06:17:29:212] 0x005C00 2% 20:05
[06:17:30:291] 0x006000 2% 19:59
[06:17:31:525] 0x006400 2% 19:59
[06:17:32:603] 0x006800 2% 19:53
[06:17:33:781] 0x006C00 2% 19:52
[06:17:34:860] 0x007000 2% 19:47
[06:17:35:985] 0x007400 2% 19:43
[06:17:38:946] All Pro firmware:
[06:17:38:977] 0x007800 2% 20:41
If you're going to do either a "Write OS, Callibration & Boot" or "Write Full Flash (Clone)" (i.e. OS swap),
1. Pay close attention to the kernel upload ... if it has errors (retries), question it!
2. ALWAYS do a Test Write, if it has errors (retries), question it!
Otherwise it's pretty darn safe, a failed "Write Calibration" is most likely recoverable.
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
Re: PCM Hammer Release 014
Gampy wrote:GeoNV,
Thank you!
You might want to juice up the battery voltage a bit ...
FYI, A debug log has everything the results log has plus more, so a debug log is a better log to post.
That log has some weird things going on in it ...
I used a OBD2link Lx. I think that's why it kept jumping between different device names.
I'll definitely be making a bench harness for it- I used to tune my 1995 Fbody LT1 and had so many near panic moments flashing it that I'll never be the same...
Looks like it loaded into Tunerpro OK as far as I can tell- the values for the tables I'm interested in all look correct. I'll do a debug log next time around. Sweet software. So nice to find this!
Re: PCM Hammer Release 014
The LX should work just fine, I do believe one of the developers (NSFW) uses one.
There should be no spurious log entries like that ... I don't see how it could even be possible.
As long as your XDF is a 12587603 xdf it should work fine.
-Enjoy
There should be no spurious log entries like that ... I don't see how it could even be possible.
As long as your XDF is a 12587603 xdf it should work fine.
-Enjoy
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
Re: PCM Hammer Release 014
I built a bench harness after a quick run to the junkyard and cloned my pcm onto it, then wrote a few changes to shift points and test wrote it and then wrote it. looks like it worked fine! I've attached the logs.
- Attachments
-
- Clone_PCM_to_Junkyard_PCM.txt
- (1.86 MiB) Downloaded 172 times
-
- debug_log_write_first_modified_tune.txt
- (616.73 KiB) Downloaded 175 times
-
- Write_First_Modified_tune_Simple_Log.txt
- (7.44 KiB) Downloaded 175 times
Re: PCM Hammer Release 014
Awesome, Looks good ...
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
Re: PCM Hammer Release 014
I even used one by NSFW! using the same xdf on the bench harness it didn't have any issues at all. Not sure what was up with the first one!Gampy wrote:The LX should work just fine, I do believe one of the developers (NSFW) uses one.
There should be no spurious log entries like that ... I don't see how it could even be possible.
As long as your XDF is a 12587603 xdf it should work fine.
-Enjoy
Re: PCM Hammer Release 014
The XDF is used by TunerPro not PcmHammer.
PcmHammer just writes/reads a binary blob to/from the Pcm through the tool.
The XDF describes where in that binary blob the Parameters are. That is how TunerPro knows where they are.
PcmHammer just writes/reads a binary blob to/from the Pcm through the tool.
The XDF describes where in that binary blob the Parameters are. That is how TunerPro knows where they are.
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
Re: PCM Hammer Release 014
hah! sorry for the confusion. Never good to let people get a glimpse of the chaos of our own minds...
Alright, just wrote wrote a tune to the truck while it was onboard- I think the issues i was having were due to the tablet computer I was using- a Dell Venue 11 Pro. I wrote it this time from a laptop and didn't have too many weird error messages. attached both the log and debug log. Also thought I could have been getting issues from having PCMHammer deep in the documents folder- I know some software gets picky about character length- so moved it to the C drive.
Alright, just wrote wrote a tune to the truck while it was onboard- I think the issues i was having were due to the tablet computer I was using- a Dell Venue 11 Pro. I wrote it this time from a laptop and didn't have too many weird error messages. attached both the log and debug log. Also thought I could have been getting issues from having PCMHammer deep in the documents folder- I know some software gets picky about character length- so moved it to the C drive.
- Attachments
-
- GeoNV_write_v2_log.txt
- (15.23 KiB) Downloaded 169 times
-
- GeoNV_write_v2_debug_log.txt
- (618.88 KiB) Downloaded 161 times
-
- Posts: 397
- Joined: Wed Jul 05, 2017 8:30 am
- cars: 2001 Pontiac Grand AM SE
LD9 2.4l I4, 4T40E
2005 Chevrolet Venture
LA1 3400 V6, 4T65E - Location: North TX, USA
Re: PCM Hammer Release 014
Hi all,GeoNV wrote:hah! sorry for the confusion. Never good to let people get a glimpse of the chaos of our own minds...
Alright, just wrote wrote a tune to the truck while it was onboard- I think the issues i was having were due to the tablet computer I was using- a Dell Venue 11 Pro. I wrote it this time from a laptop and didn't have too many weird error messages. attached both the log and debug log. Also thought I could have been getting issues from having PCMHammer deep in the documents folder- I know some software gets picky about character length- so moved it to the C drive.
GeoNV,
Pity that the Dell Tablet doesn't seem to work correctly - I was considering purchasing a Venue 8 Pro to do exactly what you were trying to do!
Oh well, guess I'll pass on that for now.
Mike