Bench harness and VCX Nano, cannot get full read p01\p59
-
- Posts: 16
- Joined: Wed Jun 01, 2022 8:02 am
- cars: 72 GMC C10 LS swapped and turbo
09 Yukon XL
18 Audi Allroad
Bench harness and VCX Nano, cannot get full read p01\p59
I have tried 4 power sources, can't seem to find one at 12-13v and over 1 amp steady. So, I cannot get a full read from PCM hammer. Same bench harness and power supply works with HPTuners.
What's the requirement here, 13v 1+ amp? My bench harness does have switched 12v constant as well as 12v ign switch.
Here's a log of last attempt and I tried 2 pcms also.
[03:45:32:285] PCM Hammer 021
[03:45:32:287] Saturday, June 25 2022 @03:45:32:28
[03:45:32:289] Initializing J2534 Device
[03:45:32:292] Loaded DLL
[03:45:34:960] Connected to the device.
[03:45:34:991] Battery Voltage is: 13.882
[03:45:35:913] Protocol Set
[03:45:35:959] Device initialization complete.
[03:46:57:784] Will save to C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PCM Hammer Reads\1st read.bin
[03:47:03:425] Querying operating system of current PCM.
[03:47:03:455] TX: 6C 10 F0 3C 0A
[03:47:03:526] RX: 6C F0 10 7C 0A 00 BF F2 4D
[03:47:03:540] OSID: 12579405
[03:47:03:577] Suppressing VPW chatter.
[03:47:03:584] TX: 6C FE F0 28 00
[03:47:03:605] Sending 'test device present' notification.
[03:47:03:613] TX: 8C FE F0 3F
[03:47:03:633] RX: 6C F0 10 68 00
[03:47:03:639] Ignoring chatter: 6C F0 10 68 00
[03:47:03:647] Sending seed request.
[03:47:03:653] TX: 6C 10 F0 27 01
[03:47:03:695] RX: 6C F0 10 67 01 4E E0
[03:47:03:698] Parsing seed value.
[03:47:03:707] Sending unlock request (4EE0, B2FF)
[03:47:03:712] TX: 6C 10 F0 27 02 B2 FF
[03:47:03:758] RX: 6C F0 10 67 02 34
[03:47:03:762] Unlock succeeded.
[03:47:03:772] Sending 'test device present' notification.
[03:47:03:781] TX: 8C FE F0 3F
[03:47:03:793] Attempting switch to VPW 4x
[03:47:03:801] TX: 6C FE F0 A0
[03:47:03:852] RX: 6C F0 10 E0 AA
[03:47:03:857] Parsing 6C F0 10 E0 AA
[03:47:03:862] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[03:47:03:870] Sending 'test device present' notification.
[03:47:03:875] TX: 8C FE F0 3F
[03:47:05:992] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:06:000] Sending 'test device present' notification.
[03:47:06:008] TX: 8C FE F0 3F
[03:47:06:024] TX: 6C FE F0 A1
[03:47:08:053] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:08:061] J2534 setting VPW 4X
[03:47:08:288] Sending 'test device present' notification.
[03:47:08:294] TX: 8C FE F0 3F
[03:47:08:306] Sending 'test device present' notification.
[03:47:08:310] TX: 8C FE F0 3F
[03:47:08:323] Loaded C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PcmHammer021\Kernel-P01.bin
[03:47:08:331] Sending upload request for kernel size 7890, loadaddress FF8000
[03:47:08:339] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:47:10:366] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:10:371] Sending 'test device present' notification.
[03:47:10:376] TX: 8C FE F0 3F
[03:47:12:398] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:12:402] Sending 'test device present' notification.
[03:47:12:405] TX: 8C FE F0 3F
[03:47:14:420] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:14:430] Sending 'test device present' notification.
[03:47:14:440] TX: 8C FE F0 3F
[03:47:16:482] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:16:493] Sending 'test device present' notification.
[03:47:16:502] TX: 8C FE F0 3F
[03:47:18:524] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:18:530] Receive timed out. Attempt #5, Timeout #5.
[03:47:18:532] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:47:20:548] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:20:551] Sending 'test device present' notification.
[03:47:20:555] TX: 8C FE F0 3F
[03:47:22:575] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:22:584] Sending 'test device present' notification.
[03:47:22:591] TX: 8C FE F0 3F
[03:47:24:620] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:24:630] Sending 'test device present' notification.
[03:47:24:636] TX: 8C FE F0 3F
[03:47:26:660] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:26:665] Sending 'test device present' notification.
[03:47:26:670] TX: 8C FE F0 3F
[03:47:28:701] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:28:708] Receive timed out. Attempt #5, Timeout #5.
[03:47:28:714] Permission to upload kernel was denied.
[03:47:28:720] If this persists, try cutting power to the PCM, restoring power, waiting ten seconds, and trying again.
[03:47:28:727] Failed to upload kernel to PCM
[03:47:28:735] Halting the kernel.
[03:47:28:739] TX: 6C 10 F0 20
[03:47:28:749] J2534 setting VPW 1X
[03:47:28:985] TX: 6C 10 F0 20
[03:47:29:006] Clearing trouble codes.
[03:47:29:264] TX: 68 6A F0 04
[03:47:29:544] TX: 68 6A F0 04
[03:47:29:811] TX: 8C FE F0 14
[03:47:30:079] TX: 8C FE F0 14
[03:47:30:096] Elapsed time 00:00:26.3286901
[03:47:30:101] Read failed, Error
[03:49:03:398] Will save to C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PCM Hammer Reads\1st read.bin
[03:49:13:495] Querying operating system of current PCM.
[03:49:13:535] TX: 6C 10 F0 3C 0A
[03:49:13:606] RX: 6C F0 10 7C 0A 00 BF F2 4D
[03:49:13:616] OSID: 12579405
[03:49:13:629] Suppressing VPW chatter.
[03:49:13:642] TX: 6C FE F0 28 00
[03:49:13:668] Sending 'test device present' notification.
[03:49:13:684] TX: 8C FE F0 3F
[03:49:13:714] RX: 6C F0 10 68 00
[03:49:13:720] Ignoring chatter: 6C F0 10 68 00
[03:49:13:725] Sending seed request.
[03:49:13:736] TX: 6C 10 F0 27 01
[03:49:13:791] RX: 6C F0 10 67 01 4E E0
[03:49:13:798] Parsing seed value.
[03:49:13:802] Sending unlock request (4EE0, B2FF)
[03:49:13:808] TX: 6C 10 F0 27 02 B2 FF
[03:49:13:868] RX: 6C F0 10 67 02 34
[03:49:13:874] Unlock succeeded.
[03:49:13:882] Sending 'test device present' notification.
[03:49:13:888] TX: 8C FE F0 3F
[03:49:13:900] Attempting switch to VPW 4x
[03:49:13:907] TX: 6C FE F0 A0
[03:49:13:962] RX: 6C F0 10 E0 AA
[03:49:13:968] Parsing 6C F0 10 E0 AA
[03:49:13:972] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[03:49:13:979] Sending 'test device present' notification.
[03:49:13:988] TX: 8C FE F0 3F
[03:49:16:120] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:16:134] Sending 'test device present' notification.
[03:49:16:147] TX: 8C FE F0 3F
[03:49:16:167] TX: 6C FE F0 A1
[03:49:18:185] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:18:192] J2534 setting VPW 4X
[03:49:18:418] Sending 'test device present' notification.
[03:49:18:433] TX: 8C FE F0 3F
[03:49:18:448] Sending 'test device present' notification.
[03:49:18:454] TX: 8C FE F0 3F
[03:49:18:464] Loaded C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PcmHammer021\Kernel-P01.bin
[03:49:18:470] Sending upload request for kernel size 7890, loadaddress FF8000
[03:49:18:478] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:49:20:510] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:20:520] Sending 'test device present' notification.
[03:49:20:525] TX: 8C FE F0 3F
[03:49:22:550] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:22:556] Sending 'test device present' notification.
[03:49:22:564] TX: 8C FE F0 3F
[03:49:24:586] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:24:599] Sending 'test device present' notification.
[03:49:24:604] TX: 8C FE F0 3F
[03:49:26:630] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:26:639] Sending 'test device present' notification.
[03:49:26:643] TX: 8C FE F0 3F
[03:49:28:663] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:28:668] Receive timed out. Attempt #5, Timeout #5.
[03:49:28:675] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:49:30:709] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:30:718] Sending 'test device present' notification.
[03:49:30:727] TX: 8C FE F0 3F
[03:49:32:745] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:32:753] Sending 'test device present' notification.
[03:49:32:765] TX: 8C FE F0 3F
[03:49:34:790] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:34:799] Sending 'test device present' notification.
[03:49:34:803] TX: 8C FE F0 3F
[03:49:36:833] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:36:848] Sending 'test device present' notification.
[03:49:36:865] TX: 8C FE F0 3F
[03:49:38:888] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:38:905] Receive timed out. Attempt #5, Timeout #5.
[03:49:38:912] Permission to upload kernel was denied.
[03:49:38:918] If this persists, try cutting power to the PCM, restoring power, waiting ten seconds, and trying again.
[03:49:38:925] Failed to upload kernel to PCM
[03:49:38:933] Halting the kernel.
[03:49:38:940] TX: 6C 10 F0 20
[03:49:38:952] J2534 setting VPW 1X
[03:49:39:185] TX: 6C 10 F0 20
[03:49:39:216] Clearing trouble codes.
[03:49:39:483] TX: 68 6A F0 04
[03:49:39:763] TX: 68 6A F0 04
[03:49:40:044] TX: 8C FE F0 14
[03:49:40:340] TX: 8C FE F0 14
[03:49:40:357] Elapsed time 00:00:26.4746234
[03:49:40:366] Read failed, Error
[03:50:16:797] TX: 6C 10 F0 3C 01
[03:50:16:857] RX: 6C F0 10 7C 01 00 33 47 4E 46 4B
[03:50:16:861] TX: 6C 10 F0 3C 02
[03:50:16:904] RX: 6C F0 10 7C 02 31 36 54 35 31 47
[03:50:16:907] TX: 6C 10 F0 3C 03
[03:50:16:966] RX: 6C F0 10 7C 03 31 31 37 39 31 34
[03:50:16:976] VIN: 3GNFK16T51G117914
[03:50:16:987] TX: 6C 10 F0 3C 0A
[03:50:17:044] RX: 6C F0 10 7C 0A 00 BA 30 68
[03:50:17:047] OS ID: 12202088
[03:50:17:055] Hardware Type: P01_P59
[03:50:17:060] TX: 6C 10 F0 3C 08
[03:50:17:106] RX: 6C F0 10 7C 08 00 BA 33 45
[03:50:17:110] Calibration ID: 12202821
[03:50:17:116] TX: 6C 10 F0 3C 04
[03:50:17:168] RX: 6C F0 10 7C 04 00 8F 3A 22
[03:50:17:172] Hardware ID: 9386530
[03:50:17:179] TX: 6C 10 F0 3C 05
[03:50:17:229] RX: 6C F0 10 7C 05 30 34 30 31
[03:50:17:232] TX: 6C 10 F0 3C 06
[03:50:17:275] RX: 6C F0 10 7C 06 31 31 38 37
[03:50:17:280] TX: 6C 10 F0 3C 07
[03:50:17:339] RX: 6C F0 10 7C 07 30 32 31 35
[03:50:17:357] Serial Number: 040111870215
[03:50:17:367] TX: 6C 10 F0 3C 14
[03:50:17:417] RX: 6C F0 10 7C 14 44 48 48 48
[03:50:17:420] Broad Cast Code: DHHH
[03:50:17:425] TX: 6C 10 F0 3C A0
[03:50:17:478] RX: 6C F0 10 7C A0 00
[03:50:17:488] MEC: 0
[03:50:29:610] Will save to C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PCM Hammer Reads\1st read.bin
[03:50:39:690] Querying operating system of current PCM.
[03:50:39:707] TX: 6C 10 F0 3C 0A
[03:50:39:776] RX: 6C F0 10 7C 0A 00 BA 30 68
[03:50:39:781] OSID: 12202088
[03:50:39:786] Suppressing VPW chatter.
[03:50:39:795] TX: 6C FE F0 28 00
[03:50:39:807] Sending 'test device present' notification.
[03:50:39:814] TX: 8C FE F0 3F
[03:50:39:839] RX: 6C F0 10 68 00
[03:50:39:848] Ignoring chatter: 6C F0 10 68 00
[03:50:39:855] Sending seed request.
[03:50:39:864] TX: 6C 10 F0 27 01
[03:50:39:917] RX: 6C F0 10 67 01 7D 3D
[03:50:39:921] Parsing seed value.
[03:50:39:924] Sending unlock request (7D3D, 55D0)
[03:50:39:926] TX: 6C 10 F0 27 02 55 D0
[03:50:39:980] RX: 6C F0 10 67 02 34
[03:50:39:984] Unlock succeeded.
[03:50:39:987] Sending 'test device present' notification.
[03:50:39:991] TX: 8C FE F0 3F
[03:50:40:012] Attempting switch to VPW 4x
[03:50:40:016] TX: 6C FE F0 A0
[03:50:40:074] RX: 6C F0 10 E0 AA
[03:50:40:077] Parsing 6C F0 10 E0 AA
[03:50:40:081] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[03:50:40:085] Sending 'test device present' notification.
[03:50:40:089] TX: 8C FE F0 3F
[03:50:42:228] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:42:234] Sending 'test device present' notification.
[03:50:42:241] TX: 8C FE F0 3F
[03:50:42:259] TX: 6C FE F0 A1
[03:50:44:277] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:44:282] J2534 setting VPW 4X
[03:50:45:291] Sending 'test device present' notification.
[03:50:45:298] TX: 8C FE F0 3F
[03:50:45:307] Sending 'test device present' notification.
[03:50:45:312] TX: 8C FE F0 3F
[03:50:45:323] Loaded C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PcmHammer021\Kernel-P01.bin
[03:50:45:326] Sending upload request for kernel size 7890, loadaddress FF8000
[03:50:45:329] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:50:47:354] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:47:363] Sending 'test device present' notification.
[03:50:47:371] TX: 8C FE F0 3F
[03:50:49:399] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:49:405] Sending 'test device present' notification.
[03:50:49:415] TX: 8C FE F0 3F
[03:50:51:443] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:51:452] Sending 'test device present' notification.
[03:50:51:457] TX: 8C FE F0 3F
[03:50:53:476] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:53:478] Sending 'test device present' notification.
[03:50:53:481] TX: 8C FE F0 3F
[03:50:55:492] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:55:502] Receive timed out. Attempt #5, Timeout #5.
[03:50:55:512] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:50:57:528] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:57:534] Sending 'test device present' notification.
[03:50:57:536] TX: 8C FE F0 3F
[03:50:59:547] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:59:556] Sending 'test device present' notification.
[03:50:59:564] TX: 8C FE F0 3F
[03:51:01:592] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:51:01:602] Sending 'test device present' notification.
[03:51:01:614] TX: 8C FE F0 3F
[03:51:03:645] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:51:03:655] Sending 'test device present' notification.
[03:51:03:663] TX: 8C FE F0 3F
[03:51:05:681] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:51:05:686] Receive timed out. Attempt #5, Timeout #5.
[03:51:05:688] Permission to upload kernel was denied.
[03:51:05:692] If this persists, try cutting power to the PCM, restoring power, waiting ten seconds, and trying again.
[03:51:05:696] Failed to upload kernel to PCM
[03:51:05:701] Halting the kernel.
[03:51:05:706] TX: 6C 10 F0 20
[03:51:05:729] J2534 setting VPW 1X
[03:51:05:965] TX: 6C 10 F0 20
[03:51:05:981] Clearing trouble codes.
[03:51:06:246] TX: 68 6A F0 04
[03:51:06:514] TX: 68 6A F0 04
[03:51:06:795] TX: 8C FE F0 14
[03:51:07:075] TX: 8C FE F0 14
[03:51:07:108] Elapsed time 00:00:27.1208431
[03:51:07:116] Read failed, Error
What's the requirement here, 13v 1+ amp? My bench harness does have switched 12v constant as well as 12v ign switch.
Here's a log of last attempt and I tried 2 pcms also.
[03:45:32:285] PCM Hammer 021
[03:45:32:287] Saturday, June 25 2022 @03:45:32:28
[03:45:32:289] Initializing J2534 Device
[03:45:32:292] Loaded DLL
[03:45:34:960] Connected to the device.
[03:45:34:991] Battery Voltage is: 13.882
[03:45:35:913] Protocol Set
[03:45:35:959] Device initialization complete.
[03:46:57:784] Will save to C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PCM Hammer Reads\1st read.bin
[03:47:03:425] Querying operating system of current PCM.
[03:47:03:455] TX: 6C 10 F0 3C 0A
[03:47:03:526] RX: 6C F0 10 7C 0A 00 BF F2 4D
[03:47:03:540] OSID: 12579405
[03:47:03:577] Suppressing VPW chatter.
[03:47:03:584] TX: 6C FE F0 28 00
[03:47:03:605] Sending 'test device present' notification.
[03:47:03:613] TX: 8C FE F0 3F
[03:47:03:633] RX: 6C F0 10 68 00
[03:47:03:639] Ignoring chatter: 6C F0 10 68 00
[03:47:03:647] Sending seed request.
[03:47:03:653] TX: 6C 10 F0 27 01
[03:47:03:695] RX: 6C F0 10 67 01 4E E0
[03:47:03:698] Parsing seed value.
[03:47:03:707] Sending unlock request (4EE0, B2FF)
[03:47:03:712] TX: 6C 10 F0 27 02 B2 FF
[03:47:03:758] RX: 6C F0 10 67 02 34
[03:47:03:762] Unlock succeeded.
[03:47:03:772] Sending 'test device present' notification.
[03:47:03:781] TX: 8C FE F0 3F
[03:47:03:793] Attempting switch to VPW 4x
[03:47:03:801] TX: 6C FE F0 A0
[03:47:03:852] RX: 6C F0 10 E0 AA
[03:47:03:857] Parsing 6C F0 10 E0 AA
[03:47:03:862] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[03:47:03:870] Sending 'test device present' notification.
[03:47:03:875] TX: 8C FE F0 3F
[03:47:05:992] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:06:000] Sending 'test device present' notification.
[03:47:06:008] TX: 8C FE F0 3F
[03:47:06:024] TX: 6C FE F0 A1
[03:47:08:053] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:08:061] J2534 setting VPW 4X
[03:47:08:288] Sending 'test device present' notification.
[03:47:08:294] TX: 8C FE F0 3F
[03:47:08:306] Sending 'test device present' notification.
[03:47:08:310] TX: 8C FE F0 3F
[03:47:08:323] Loaded C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PcmHammer021\Kernel-P01.bin
[03:47:08:331] Sending upload request for kernel size 7890, loadaddress FF8000
[03:47:08:339] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:47:10:366] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:10:371] Sending 'test device present' notification.
[03:47:10:376] TX: 8C FE F0 3F
[03:47:12:398] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:12:402] Sending 'test device present' notification.
[03:47:12:405] TX: 8C FE F0 3F
[03:47:14:420] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:14:430] Sending 'test device present' notification.
[03:47:14:440] TX: 8C FE F0 3F
[03:47:16:482] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:16:493] Sending 'test device present' notification.
[03:47:16:502] TX: 8C FE F0 3F
[03:47:18:524] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:18:530] Receive timed out. Attempt #5, Timeout #5.
[03:47:18:532] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:47:20:548] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:20:551] Sending 'test device present' notification.
[03:47:20:555] TX: 8C FE F0 3F
[03:47:22:575] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:22:584] Sending 'test device present' notification.
[03:47:22:591] TX: 8C FE F0 3F
[03:47:24:620] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:24:630] Sending 'test device present' notification.
[03:47:24:636] TX: 8C FE F0 3F
[03:47:26:660] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:26:665] Sending 'test device present' notification.
[03:47:26:670] TX: 8C FE F0 3F
[03:47:28:701] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:47:28:708] Receive timed out. Attempt #5, Timeout #5.
[03:47:28:714] Permission to upload kernel was denied.
[03:47:28:720] If this persists, try cutting power to the PCM, restoring power, waiting ten seconds, and trying again.
[03:47:28:727] Failed to upload kernel to PCM
[03:47:28:735] Halting the kernel.
[03:47:28:739] TX: 6C 10 F0 20
[03:47:28:749] J2534 setting VPW 1X
[03:47:28:985] TX: 6C 10 F0 20
[03:47:29:006] Clearing trouble codes.
[03:47:29:264] TX: 68 6A F0 04
[03:47:29:544] TX: 68 6A F0 04
[03:47:29:811] TX: 8C FE F0 14
[03:47:30:079] TX: 8C FE F0 14
[03:47:30:096] Elapsed time 00:00:26.3286901
[03:47:30:101] Read failed, Error
[03:49:03:398] Will save to C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PCM Hammer Reads\1st read.bin
[03:49:13:495] Querying operating system of current PCM.
[03:49:13:535] TX: 6C 10 F0 3C 0A
[03:49:13:606] RX: 6C F0 10 7C 0A 00 BF F2 4D
[03:49:13:616] OSID: 12579405
[03:49:13:629] Suppressing VPW chatter.
[03:49:13:642] TX: 6C FE F0 28 00
[03:49:13:668] Sending 'test device present' notification.
[03:49:13:684] TX: 8C FE F0 3F
[03:49:13:714] RX: 6C F0 10 68 00
[03:49:13:720] Ignoring chatter: 6C F0 10 68 00
[03:49:13:725] Sending seed request.
[03:49:13:736] TX: 6C 10 F0 27 01
[03:49:13:791] RX: 6C F0 10 67 01 4E E0
[03:49:13:798] Parsing seed value.
[03:49:13:802] Sending unlock request (4EE0, B2FF)
[03:49:13:808] TX: 6C 10 F0 27 02 B2 FF
[03:49:13:868] RX: 6C F0 10 67 02 34
[03:49:13:874] Unlock succeeded.
[03:49:13:882] Sending 'test device present' notification.
[03:49:13:888] TX: 8C FE F0 3F
[03:49:13:900] Attempting switch to VPW 4x
[03:49:13:907] TX: 6C FE F0 A0
[03:49:13:962] RX: 6C F0 10 E0 AA
[03:49:13:968] Parsing 6C F0 10 E0 AA
[03:49:13:972] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[03:49:13:979] Sending 'test device present' notification.
[03:49:13:988] TX: 8C FE F0 3F
[03:49:16:120] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:16:134] Sending 'test device present' notification.
[03:49:16:147] TX: 8C FE F0 3F
[03:49:16:167] TX: 6C FE F0 A1
[03:49:18:185] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:18:192] J2534 setting VPW 4X
[03:49:18:418] Sending 'test device present' notification.
[03:49:18:433] TX: 8C FE F0 3F
[03:49:18:448] Sending 'test device present' notification.
[03:49:18:454] TX: 8C FE F0 3F
[03:49:18:464] Loaded C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PcmHammer021\Kernel-P01.bin
[03:49:18:470] Sending upload request for kernel size 7890, loadaddress FF8000
[03:49:18:478] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:49:20:510] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:20:520] Sending 'test device present' notification.
[03:49:20:525] TX: 8C FE F0 3F
[03:49:22:550] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:22:556] Sending 'test device present' notification.
[03:49:22:564] TX: 8C FE F0 3F
[03:49:24:586] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:24:599] Sending 'test device present' notification.
[03:49:24:604] TX: 8C FE F0 3F
[03:49:26:630] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:26:639] Sending 'test device present' notification.
[03:49:26:643] TX: 8C FE F0 3F
[03:49:28:663] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:28:668] Receive timed out. Attempt #5, Timeout #5.
[03:49:28:675] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:49:30:709] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:30:718] Sending 'test device present' notification.
[03:49:30:727] TX: 8C FE F0 3F
[03:49:32:745] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:32:753] Sending 'test device present' notification.
[03:49:32:765] TX: 8C FE F0 3F
[03:49:34:790] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:34:799] Sending 'test device present' notification.
[03:49:34:803] TX: 8C FE F0 3F
[03:49:36:833] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:36:848] Sending 'test device present' notification.
[03:49:36:865] TX: 8C FE F0 3F
[03:49:38:888] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:49:38:905] Receive timed out. Attempt #5, Timeout #5.
[03:49:38:912] Permission to upload kernel was denied.
[03:49:38:918] If this persists, try cutting power to the PCM, restoring power, waiting ten seconds, and trying again.
[03:49:38:925] Failed to upload kernel to PCM
[03:49:38:933] Halting the kernel.
[03:49:38:940] TX: 6C 10 F0 20
[03:49:38:952] J2534 setting VPW 1X
[03:49:39:185] TX: 6C 10 F0 20
[03:49:39:216] Clearing trouble codes.
[03:49:39:483] TX: 68 6A F0 04
[03:49:39:763] TX: 68 6A F0 04
[03:49:40:044] TX: 8C FE F0 14
[03:49:40:340] TX: 8C FE F0 14
[03:49:40:357] Elapsed time 00:00:26.4746234
[03:49:40:366] Read failed, Error
[03:50:16:797] TX: 6C 10 F0 3C 01
[03:50:16:857] RX: 6C F0 10 7C 01 00 33 47 4E 46 4B
[03:50:16:861] TX: 6C 10 F0 3C 02
[03:50:16:904] RX: 6C F0 10 7C 02 31 36 54 35 31 47
[03:50:16:907] TX: 6C 10 F0 3C 03
[03:50:16:966] RX: 6C F0 10 7C 03 31 31 37 39 31 34
[03:50:16:976] VIN: 3GNFK16T51G117914
[03:50:16:987] TX: 6C 10 F0 3C 0A
[03:50:17:044] RX: 6C F0 10 7C 0A 00 BA 30 68
[03:50:17:047] OS ID: 12202088
[03:50:17:055] Hardware Type: P01_P59
[03:50:17:060] TX: 6C 10 F0 3C 08
[03:50:17:106] RX: 6C F0 10 7C 08 00 BA 33 45
[03:50:17:110] Calibration ID: 12202821
[03:50:17:116] TX: 6C 10 F0 3C 04
[03:50:17:168] RX: 6C F0 10 7C 04 00 8F 3A 22
[03:50:17:172] Hardware ID: 9386530
[03:50:17:179] TX: 6C 10 F0 3C 05
[03:50:17:229] RX: 6C F0 10 7C 05 30 34 30 31
[03:50:17:232] TX: 6C 10 F0 3C 06
[03:50:17:275] RX: 6C F0 10 7C 06 31 31 38 37
[03:50:17:280] TX: 6C 10 F0 3C 07
[03:50:17:339] RX: 6C F0 10 7C 07 30 32 31 35
[03:50:17:357] Serial Number: 040111870215
[03:50:17:367] TX: 6C 10 F0 3C 14
[03:50:17:417] RX: 6C F0 10 7C 14 44 48 48 48
[03:50:17:420] Broad Cast Code: DHHH
[03:50:17:425] TX: 6C 10 F0 3C A0
[03:50:17:478] RX: 6C F0 10 7C A0 00
[03:50:17:488] MEC: 0
[03:50:29:610] Will save to C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PCM Hammer Reads\1st read.bin
[03:50:39:690] Querying operating system of current PCM.
[03:50:39:707] TX: 6C 10 F0 3C 0A
[03:50:39:776] RX: 6C F0 10 7C 0A 00 BA 30 68
[03:50:39:781] OSID: 12202088
[03:50:39:786] Suppressing VPW chatter.
[03:50:39:795] TX: 6C FE F0 28 00
[03:50:39:807] Sending 'test device present' notification.
[03:50:39:814] TX: 8C FE F0 3F
[03:50:39:839] RX: 6C F0 10 68 00
[03:50:39:848] Ignoring chatter: 6C F0 10 68 00
[03:50:39:855] Sending seed request.
[03:50:39:864] TX: 6C 10 F0 27 01
[03:50:39:917] RX: 6C F0 10 67 01 7D 3D
[03:50:39:921] Parsing seed value.
[03:50:39:924] Sending unlock request (7D3D, 55D0)
[03:50:39:926] TX: 6C 10 F0 27 02 55 D0
[03:50:39:980] RX: 6C F0 10 67 02 34
[03:50:39:984] Unlock succeeded.
[03:50:39:987] Sending 'test device present' notification.
[03:50:39:991] TX: 8C FE F0 3F
[03:50:40:012] Attempting switch to VPW 4x
[03:50:40:016] TX: 6C FE F0 A0
[03:50:40:074] RX: 6C F0 10 E0 AA
[03:50:40:077] Parsing 6C F0 10 E0 AA
[03:50:40:081] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[03:50:40:085] Sending 'test device present' notification.
[03:50:40:089] TX: 8C FE F0 3F
[03:50:42:228] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:42:234] Sending 'test device present' notification.
[03:50:42:241] TX: 8C FE F0 3F
[03:50:42:259] TX: 6C FE F0 A1
[03:50:44:277] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:44:282] J2534 setting VPW 4X
[03:50:45:291] Sending 'test device present' notification.
[03:50:45:298] TX: 8C FE F0 3F
[03:50:45:307] Sending 'test device present' notification.
[03:50:45:312] TX: 8C FE F0 3F
[03:50:45:323] Loaded C:\Users\super\OneDrive\Desktop\Tuning\VX Diag\PcmHammer021\Kernel-P01.bin
[03:50:45:326] Sending upload request for kernel size 7890, loadaddress FF8000
[03:50:45:329] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:50:47:354] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:47:363] Sending 'test device present' notification.
[03:50:47:371] TX: 8C FE F0 3F
[03:50:49:399] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:49:405] Sending 'test device present' notification.
[03:50:49:415] TX: 8C FE F0 3F
[03:50:51:443] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:51:452] Sending 'test device present' notification.
[03:50:51:457] TX: 8C FE F0 3F
[03:50:53:476] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:53:478] Sending 'test device present' notification.
[03:50:53:481] TX: 8C FE F0 3F
[03:50:55:492] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:55:502] Receive timed out. Attempt #5, Timeout #5.
[03:50:55:512] TX: 6C 10 F0 34 00 10 00 FF 80 00
[03:50:57:528] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:57:534] Sending 'test device present' notification.
[03:50:57:536] TX: 8C FE F0 3F
[03:50:59:547] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:50:59:556] Sending 'test device present' notification.
[03:50:59:564] TX: 8C FE F0 3F
[03:51:01:592] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:51:01:602] Sending 'test device present' notification.
[03:51:01:614] TX: 8C FE F0 3F
[03:51:03:645] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:51:03:655] Sending 'test device present' notification.
[03:51:03:663] TX: 8C FE F0 3F
[03:51:05:681] ReadMsgs OBDError: ERR_BUFFER_EMPTY
[03:51:05:686] Receive timed out. Attempt #5, Timeout #5.
[03:51:05:688] Permission to upload kernel was denied.
[03:51:05:692] If this persists, try cutting power to the PCM, restoring power, waiting ten seconds, and trying again.
[03:51:05:696] Failed to upload kernel to PCM
[03:51:05:701] Halting the kernel.
[03:51:05:706] TX: 6C 10 F0 20
[03:51:05:729] J2534 setting VPW 1X
[03:51:05:965] TX: 6C 10 F0 20
[03:51:05:981] Clearing trouble codes.
[03:51:06:246] TX: 68 6A F0 04
[03:51:06:514] TX: 68 6A F0 04
[03:51:06:795] TX: 8C FE F0 14
[03:51:07:075] TX: 8C FE F0 14
[03:51:07:108] Elapsed time 00:00:27.1208431
[03:51:07:116] Read failed, Error
Re: Bench harness and VCX Nano, cannot get full read p01\p59
+13.8v is beautiful.
I was more concerned with the PCM pinout on the bench harness, there are some done differently ...
Big hardware difference between HPT and PcmHammer ... The VCI.
The Nano should have the latest and greatest firmware, if I understand correctly the Nano FORCES updates or quits working. Stupid control freaks!
They are also widely used with PcmHammer.
It is not getting a response at all from the mode 34 request ...
I was more concerned with the PCM pinout on the bench harness, there are some done differently ...
Big hardware difference between HPT and PcmHammer ... The VCI.
The Nano should have the latest and greatest firmware, if I understand correctly the Nano FORCES updates or quits working. Stupid control freaks!
They are also widely used with PcmHammer.
It is not getting a response at all from the mode 34 request ...
Do you by any chance have any other VCI's, like another J2534 or even an ELM, something that is PcmHammer compatible, it would be very helpful to have a bus log ...[03:47:08:339] TX: 6C 10 F0 34 00 10 00 FF 80 00
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
-
- Posts: 16
- Joined: Wed Jun 01, 2022 8:02 am
- cars: 72 GMC C10 LS swapped and turbo
09 Yukon XL
18 Audi Allroad
Re: Bench harness and VCX Nano, cannot get full read p01\p59
Only the vcx nano.
I'll triple check obd2 pinning.
I'll triple check obd2 pinning.
-
- Posts: 305
- Joined: Fri Jul 30, 2021 5:49 pm
- cars: 97 Corvette
92 Camaro
2005 Silverado
2001 Savana 2500
1998 c3500hd
1998 tahoe
Re: Bench harness and VCX Nano, cannot get full read p01\p59
This reminds me of my attempt at reading a p04 PCM. I got same error iirc. Are you sure these are p01/p59? What does hptuners say?
- antus
- Site Admin
- Posts: 8253
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Bench harness and VCX Nano, cannot get full read p01\p59
12202088 is a P01 OSID so unless someone has gone way out of their way to mess things up, I believe it is a P01. There is something else wrong here, power/writing/faulty pcm/something else? Cant really say from the above, but can see it stops responding when it gets asked for permission to upload the kernel. Does version 20 work?
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 305
- Joined: Fri Jul 30, 2021 5:49 pm
- cars: 97 Corvette
92 Camaro
2005 Silverado
2001 Savana 2500
1998 c3500hd
1998 tahoe
Re: Bench harness and VCX Nano, cannot get full read p01\p59
Also, the nano won't even try to work if it doesn't have a good license which has to be updated every 60 days, and you can't get a license if you don't have the newest firmware. So the fact that he can communicate with it means his firmware and license are new. My nano works fine, so i don't think it's a nano issue, though I don't know that for certain.
-
- Posts: 16
- Joined: Wed Jun 01, 2022 8:02 am
- cars: 72 GMC C10 LS swapped and turbo
09 Yukon XL
18 Audi Allroad
Re: Bench harness and VCX Nano, cannot get full read p01\p59
I am confused on licensing for Nano, I have not done any licensing at all. Found on their page that they do $0.10 licenses but not sure what for. Working on this some more later today some more, fingers crossed.Cincinnatus wrote:Also, the nano won't even try to work if it doesn't have a good license which has to be updated every 60 days, and you can't get a license if you don't have the newest firmware. So the fact that he can communicate with it means his firmware and license are new. My nano works fine, so i don't think it's a nano issue, though I don't know that for certain.
-
- Posts: 16
- Joined: Wed Jun 01, 2022 8:02 am
- cars: 72 GMC C10 LS swapped and turbo
09 Yukon XL
18 Audi Allroad
Re: Bench harness and VCX Nano, cannot get full read p01\p59
Have tried both p01 and p59, so yes...that was a p01. Finding more guys wanting these lately on swaps because they're sick of playing the TB/TAC/ECU game when they don't get it all as a package.antus wrote:12202088 is a P01 OSID so unless someone has gone way out of their way to mess things up, I believe it is a P01. There is something else wrong here, power/writing/faulty pcm/something else? Cant really say from the above, but can see it stops responding when it gets asked for permission to upload the kernel. Does version 20 work?
I'll have to try v20 later today when I get a chance.
Last edited by MercRising on Mon Jun 27, 2022 2:39 am, edited 1 time in total.
-
- Posts: 305
- Joined: Fri Jul 30, 2021 5:49 pm
- cars: 97 Corvette
92 Camaro
2005 Silverado
2001 Savana 2500
1998 c3500hd
1998 tahoe
Re: Bench harness and VCX Nano, cannot get full read p01\p59
?????? You haven't installed vx manager? Then just install the j2534 passthru driver. Newest version of vx manager will update license automatically. I'm surprised you get any communication through the tool without it. What driver did you install?
-
- Posts: 16
- Joined: Wed Jun 01, 2022 8:02 am
- cars: 72 GMC C10 LS swapped and turbo
09 Yukon XL
18 Audi Allroad
Re: Bench harness and VCX Nano, cannot get full read p01\p59
Cincinnatus, it did force a firmware update when I first got it speaking to their VX Diag software. Do I need to do anything else since I bought the GM specific one? When I set up, all I installed were GM and j2534. I was under impression this was not a licensing required tool unless I wanted to get on ACDelco for GM stock files.