PCMHacking Frequently Asked Questions (FAQ)

Holden/Delco Tuning. ALDL, OBD 1.5. Circa 1989 to 2004.
Posts: 8
Joined: Tue Jul 03, 2018 10:32 pm

Re: PCMHacking Frequently Asked Questions (FAQ)

Postby LT1truck » Tue Jul 17, 2018 1:54 pm

thanks very much!

Posts: 49
Joined: Sun Jul 24, 2016 4:38 pm

Re: PCMHacking Frequently Asked Questions (FAQ)

Postby vHell83 » Fri Mar 01, 2019 9:18 pm

hi, I am trying to write to a 29ee010 chip with a GX 4x4 chip burner.

I cannot find the above chip type, the closet I find is 29F002 which is 256KB vs 128KB (The chip in the burner)

I decided to try and write to it anyway, i used HxD to verify and the parameters are way off. Could someone please point me in the right direction?

Below are relevant codes

Image
Image

c:\users\user\desktop\vx_v6_sc_%24a5k_enhanced_v1.3f\vxnovat.bin.
Configuration OK!
This software is updated already.
<<29F002>>
ID check skipped
Reading... Buffer
Elapsed time: 7.32 seconds.
Read completed.
ID check skipped
Writing... Buffer
Elapsed time: 2.72 seconds.
Device write completed OK
ID check skipped
Verifying... Buffer
Device is verified
Elapsed time: 7.34 seconds.

Site Admin
User avatar
Posts: 7206
Joined: Sat Feb 28, 2009 8:34 pm

Re: PCMHacking Frequently Asked Questions (FAQ)

Postby antus » Fri Mar 01, 2019 9:49 pm

Please start a new thread for this. But short answer is thats a flash memory, not the traditional eeprom type we mostly use and being page erase your going to need the right memory mapping, close but not the same wont work.
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

Posts: 12
Joined: Wed May 29, 2019 11:17 am
Location: Perth WA

ACRONYMS

Postby nikolatesla » Fri May 31, 2019 5:31 pm

This seems to be missing so I thought it would be good to add it as i had to search else where for it ...I did not read every post so apologies if this is a repeat.

PCM, Powertrain Control Module
BCM, Body Control Module
ECU, Electronic Control Unit, (generic term, ie. "Engine ECU")
ECM, Engine Control Module
TCM, Transmission Control Module
TDM, Theft Deterrent Module

please correct and delete if this info is wrong in any way .
Other wise it should be on the first page

Site Admin
User avatar
Posts: 7206
Joined: Sat Feb 28, 2009 8:34 pm

Re: PCMHacking Frequently Asked Questions (FAQ)

Postby antus » Fri Nov 08, 2019 12:37 pm

Just added the first P01 / P59 entry to the FAQ! hooray!
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

Posts: 3269
Joined: Mon Aug 02, 2010 6:35 pm

Re: PCMHacking Frequently Asked Questions (FAQ)

Postby Dylan » Fri Nov 08, 2019 4:01 pm

antus wrote:Just added the first P01 / P59 entry to the FAQ! hooray!



How awesome is that!

Posts: 53
Joined: Fri Mar 06, 2015 4:54 pm

Re: PCMHacking Frequently Asked Questions (FAQ)

Postby big cams » Sun Feb 06, 2022 12:36 pm

hi all

is there a step by step on how to set up 11p system and 12p system?

Site Admin
User avatar
Posts: 7206
Joined: Sat Feb 28, 2009 8:34 pm

Re: PCMHacking Frequently Asked Questions (FAQ)

Postby antus » Sun Feb 06, 2022 1:22 pm

We have the 12p guides in the first post, but there isnt more detail than that, sorry. generally speaking its setup jumpers on the nvram to set cylinders and pcm for the 11p computers. load the calibration for the closest factory tune, set flags for map sensor type, set injector rate and battery voltage delay, set cranking time stage 1 and 2 by percentage of difference between stock injectors and what you've got, then tune ve and spark.
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

Posts: 53
Joined: Fri Mar 06, 2015 4:54 pm

Re: PCMHacking Frequently Asked Questions (FAQ)

Postby big cams » Sun Feb 06, 2022 2:16 pm

ok no worrys thank you

Previous

Return to Holden ALDL ECUs

Who is online

Users browsing this forum: No registered users and 9 guests