PCMHacking Frequently Asked Questions (FAQ)

Holden/Delco Tuning. ALDL, OBD 1.5. Circa 1989 to 2004.
LT1truck
Posts: 8
Joined: Tue Jul 03, 2018 10:32 pm
cars: LS3VK
LS3 67 Camaro
LT1 C1500

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by LT1truck »

thanks very much!
vHell83
Posts: 49
Joined: Sun Jul 24, 2016 4:38 pm
cars: Supercharged VH V6

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by vHell83 »

hi, I am trying to write to a 29ee010 chip with a GX 4x4 chip burner.

I cannot find the above chip type, the closet I find is 29F002 which is 256KB vs 128KB (The chip in the burner)

I decided to try and write to it anyway, i used HxD to verify and the parameters are way off. Could someone please point me in the right direction?

Below are relevant codes

Image
Image

c:\users\user\desktop\vx_v6_sc_%24a5k_enhanced_v1.3f\vxnovat.bin.
Configuration OK!
This software is updated already.
<<29F002>>
ID check skipped
Reading... Buffer
Elapsed time: 7.32 seconds.
Read completed.
ID check skipped
Writing... Buffer
Elapsed time: 2.72 seconds.
Device write completed OK
ID check skipped
Verifying... Buffer
Device is verified
Elapsed time: 7.34 seconds.
User avatar
antus
Site Admin
Posts: 8375
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by antus »

Please start a new thread for this. But short answer is thats a flash memory, not the traditional eeprom type we mostly use and being page erase your going to need the right memory mapping, close but not the same wont work.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
nikolatesla
Posts: 12
Joined: Wed May 29, 2019 11:17 am
cars: vx sedan vy ute
Location: Perth WA

ACRONYMS

Post by nikolatesla »

This seems to be missing so I thought it would be good to add it as i had to search else where for it ...I did not read every post so apologies if this is a repeat.

PCM, Powertrain Control Module
BCM, Body Control Module
ECU, Electronic Control Unit, (generic term, ie. "Engine ECU")
ECM, Engine Control Module
TCM, Transmission Control Module
TDM, Theft Deterrent Module

please correct and delete if this info is wrong in any way .
Other wise it should be on the first page
User avatar
antus
Site Admin
Posts: 8375
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by antus »

Just added the first P01 / P59 entry to the FAQ! hooray!
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Dylan
Posts: 3357
Joined: Mon Aug 02, 2010 6:35 pm
cars: VR Commodore V8

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by Dylan »

antus wrote:Just added the first P01 / P59 entry to the FAQ! hooray!

How awesome is that!
big cams
Posts: 53
Joined: Fri Mar 06, 2015 4:54 pm
cars: lots of holdens

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by big cams »

hi all

is there a step by step on how to set up 11p system and 12p system?
User avatar
antus
Site Admin
Posts: 8375
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by antus »

We have the 12p guides in the first post, but there isnt more detail than that, sorry. generally speaking its setup jumpers on the nvram to set cylinders and pcm for the 11p computers. load the calibration for the closest factory tune, set flags for map sensor type, set injector rate and battery voltage delay, set cranking time stage 1 and 2 by percentage of difference between stock injectors and what you've got, then tune ve and spark.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
big cams
Posts: 53
Joined: Fri Mar 06, 2015 4:54 pm
cars: lots of holdens

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by big cams »

ok no worrys thank you
bachig24u
Posts: 28
Joined: Tue Dec 13, 2011 2:59 pm
cars: R33 Skyline, ethanol burning starlet turbo, yours until its tuned!
Location: Campbelltown, NSW
Contact:

424 PCM wiring NV RAM

Post by bachig24u »

Hi,
Can anyone tell me if using the PCM with a stock MEMcal back in it,
and leaving the wire that was soldered in underneath the board still attached will cause an issue?

I can seem to find any mention about it.

Kr
Sime
Kind regards
Sime
Post Reply