VS Memcal - Help
VS Memcal - Help
Hi .. im new to flashing Memcals but not to chip flashing... do a fair bit of LS1 work and they are easy compared to these .hahahah.
my problem is i am trying to remove security from a VS chip. I have read the memcal in my willem programmer and then modified it with tunerpro and then burn it back (after erasing UV ) the memcal
car wont start at all (even with the VATS bypass box)
I have even tried reading the stock tune from on memcal which starts the car and then burning that onto a memcal and trying... but just ont do it.
how do i know i am choosing the correct chip in the willem programmer.. the markings on the chip are nothing that really identify it
has the following
014
07957
B9525TB
3 others i have tried and have similar markings... I have been choosing 27C010 or similar (ie NM27C010)
it is becoming very frustrating and if anyone can give any pointers it would be great
what voltages are you running on the willem (just USB or aux 12v)
my problem is i am trying to remove security from a VS chip. I have read the memcal in my willem programmer and then modified it with tunerpro and then burn it back (after erasing UV ) the memcal
car wont start at all (even with the VATS bypass box)
I have even tried reading the stock tune from on memcal which starts the car and then burning that onto a memcal and trying... but just ont do it.
how do i know i am choosing the correct chip in the willem programmer.. the markings on the chip are nothing that really identify it
has the following
014
07957
B9525TB
3 others i have tried and have similar markings... I have been choosing 27C010 or similar (ie NM27C010)
it is becoming very frustrating and if anyone can give any pointers it would be great
what voltages are you running on the willem (just USB or aux 12v)
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: VS Memcal - Help
yes vs use 27C010 what is the jumper to the left of the dip switches set on the lower 2 pins or upper 2 pins
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: VS Memcal - Help
need to change the checksum ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: VS Memcal - Help
still runs with the wrong checksum just get error 51 immortality had the same issue with 27c010's in the willem then we found that jumper was up not down makes it suit other chips by the time he changed it he had burned all his 27c010's so hasnt had a good one to try since moving the jumper it was the only hardware difference between my burner and his might have fried his chips they still dont work after changing the jumper
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: VS Memcal - Help
i assume you are talking about the willem. mine doesn thave dip switches
its the GQ-3X USB version.. has the header pins and they are all free
checksums?
sorry for my ignorance...
its the GQ-3X USB version.. has the header pins and they are all free
checksums?
sorry for my ignorance...
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: VS Memcal - Help
when you change the bin and save it that can cause checksum issues ....
i have erased and burnt 010 chips no worries so it should be easily doable.
i have erased and burnt 010 chips no worries so it should be easily doable.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: VS Memcal - Help
i have no doubt it is easily done but mine arent working.. when it writes to the chip then verifies it is fine but if i read it then sometimes they com eback blank again... i assume it is all to do with the programmer and setting it up correctly but not sure what
Re: VS Memcal - Help
is a 27c010 a eprom or eeprom? i am using eproms (UV erasable)
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: VS Memcal - Help
eprom = uv erasable
eeprom = electronically erasable
this is how i normally set mine up.
in the eprom list go eprom -> 27Cxxx -> 27C010
eeprom = electronically erasable
this is how i normally set mine up.
in the eprom list go eprom -> 27Cxxx -> 27C010
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: VS Memcal - Help
mine is totally different