Thats correct holden202t,
I will take a log this arvo and post everything when i get home.
Innovate MTX-L Wideband O2 Sensor ISSUE
-
- Posts: 16
- Joined: Tue May 22, 2018 9:50 pm
- cars: VT Sedan Acclaim II 3.8L V6
-
- Posts: 16
- Joined: Tue May 22, 2018 9:50 pm
- cars: VT Sedan Acclaim II 3.8L V6
Re: Innovate MTX-L Wideband O2 Sensor ISSUE
I have attached all the tune files i'm using plus a log of a short drive
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Innovate MTX-L Wideband O2 Sensor ISSUE
I don't believe there are any issues with the way the adx is configured, its certainly got the right calc for wideband on Pin A5 input.
running through your log though and the wideband input is pretty much stuck on 16.85 the whole time except for one or two small blips, which leads me to think either there is some wiring issue, or the config on the mtx-l itself for the analog output is not setup right....
please confirm which colour wire is connected to pin A5
and also confirm you have the analog output settings on the MTX-L configured as per below ?
Also just for your info, as you can see below, this history table is configured to plot the wideband analog input reading ... so if everything is right, the numbers in this table should match what you see on the wideband gauge.
This one however is a multiplier, so it will take the wideband input reading and multiply it with the commanded air fuel ratio, to provide you with a number which should allow you to directly multiply the injector offset table.
I've also edited your ADX so the wideband readings are the same for analog input and the commanded AFR .... this will mean looking at the monitor if they are the same number they will be over the top of each other.
running through your log though and the wideband input is pretty much stuck on 16.85 the whole time except for one or two small blips, which leads me to think either there is some wiring issue, or the config on the mtx-l itself for the analog output is not setup right....
please confirm which colour wire is connected to pin A5
and also confirm you have the analog output settings on the MTX-L configured as per below ?
Also just for your info, as you can see below, this history table is configured to plot the wideband analog input reading ... so if everything is right, the numbers in this table should match what you see on the wideband gauge.
This one however is a multiplier, so it will take the wideband input reading and multiply it with the commanded air fuel ratio, to provide you with a number which should allow you to directly multiply the injector offset table.
I've also edited your ADX so the wideband readings are the same for analog input and the commanded AFR .... this will mean looking at the monitor if they are the same number they will be over the top of each other.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
-
- Posts: 16
- Joined: Tue May 22, 2018 9:50 pm
- cars: VT Sedan Acclaim II 3.8L V6
Re: Innovate MTX-L Wideband O2 Sensor ISSUE
Thankyou heaps Holden202T,
I only discovered the wideband reading 16.85 static when i took the log. I have the wideband setup using the YELLOW anaglog 1 setup as per your screen shot. Even with the wideband disconnected the table still reads 16.85 so im not sure whats going on. I have douvke checked all the wiring and its all setup 100%.
I appreciate the assistance!
I only discovered the wideband reading 16.85 static when i took the log. I have the wideband setup using the YELLOW anaglog 1 setup as per your screen shot. Even with the wideband disconnected the table still reads 16.85 so im not sure whats going on. I have douvke checked all the wiring and its all setup 100%.
I appreciate the assistance!
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Innovate MTX-L Wideband O2 Sensor ISSUE
You can set the innovate wideband to output a fixed voltage during warm up, good for a sanity check that things are working ok. Also during testing or fault finding of offsets you can do the same when its warm, so you can get two voltage points to compare offsets with. Speeds up finding ground offsets as you can try various things without needing to drive the car.
-
- Posts: 16
- Joined: Tue May 22, 2018 9:50 pm
- cars: VT Sedan Acclaim II 3.8L V6
Re: Innovate MTX-L Wideband O2 Sensor ISSUE
Thanks VL400, I'll have a play with it but i dont think that will fix the issue i'm having. when logging tunerpro only reads 16.85 static no change across the board it just plots 16.85 over the load table.