12p onto a 27c128??????
-
- Posts: 130
- Joined: Tue Nov 29, 2016 2:59 pm
- cars: bf xr6 turbo
vs ss
vr clubsport - Location: Rockhampton
Re: 12p onto a 27c128??????
Bloody legend, now I just need a crash course on desoldering and fitting those without making it look like it’s been through a house fire.
Also does using those mean it doesn’t matter what type of me cal you use ie v6 v8 ect ect?? Because I’ve got a few v6 memcals kicking around
Also does using those mean it doesn’t matter what type of me cal you use ie v6 v8 ect ect?? Because I’ve got a few v6 memcals kicking around
- vlad01
- Posts: 7801
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: 12p onto a 27c128??????
A small butter knife and small pick tool, pry each side up so the socket tabs lift up with the chip, thin tip soldering iron that's clean you heat and push those tabs down again one at a time. Then you pry up again with the knife/pick and repeat cycle until the tabs are no longer soldered to the pins.
I recommend soldering in a machined socket in place of the chip for ease of removal latter.
I recommend soldering in a machined socket in place of the chip for ease of removal latter.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
- Posts: 130
- Joined: Tue Nov 29, 2016 2:59 pm
- cars: bf xr6 turbo
vs ss
vr clubsport - Location: Rockhampton
Re: 12p onto a 27c128??????
I did a trial run unpicking one today and that’s pretty much how I did it and it worked well enough but soldering it back in was an issue, I couldn’t get the programmer to I’d it afterwards so I must have put to much heat into it maybe
- vlad01
- Posts: 7801
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: 12p onto a 27c128??????
I had one die like that too. Some of the address lines internally shorted or something as it wrote the same data to 2 places on the chip at the same time. Still did it even after I removed it and tried in the programmer by itself. This is why I use a socket first and then install the chip into that. Makes programing easy too as you don't need an adapter.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: 12p onto a 27c128??????
Sweet. I've just ordered some. I had a bad tune recently as my uv eraser is getting old and tired and taking almost an hour to erase a chip.delcowizzid wrote: https://www.ebay.com/itm/10pcs-W27C512- ... %7Ciid%3A1
Second lot I've got through this guy I love not having to erase eprom anymore lol
-
- Posts: 130
- Joined: Tue Nov 29, 2016 2:59 pm
- cars: bf xr6 turbo
vs ss
vr clubsport - Location: Rockhampton
Re: 12p onto a 27c128??????
My thoughts also, have you got a link to the adapter and where you get them from?vlad01 wrote:I had one die like that too. Some of the address lines internally shorted or something as it wrote the same data to 2 places on the chip at the same time. Still did it even after I removed it and tried in the programmer by itself. This is why I use a socket first and then install the chip into that. Makes programing easy too as you don't need an adapter.
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
12p onto a 27c128??????
Jaycar should have the machined sockets you need.
-
- Posts: 130
- Joined: Tue Nov 29, 2016 2:59 pm
- cars: bf xr6 turbo
vs ss
vr clubsport - Location: Rockhampton
Re: 12p onto a 27c128??????
Awesomeimmortality wrote:Jaycar should have the machined sockets you need.
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: 12p onto a 27c128??????
https://www.ebay.com/itm/10pc-DIP-IC-So ... XQdx5RFfGD
https://www.ebay.com/itm/50pcs-28Pin-wi ... Swv-NWVAa8
10 or 50 or can buy them singly probably cheaper ones if you go looking just make sure they are machine tool sockets not the flat slot kind
https://www.ebay.com/itm/50pcs-28Pin-wi ... Swv-NWVAa8
10 or 50 or can buy them singly probably cheaper ones if you go looking just make sure they are machine tool sockets not the flat slot kind
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
- Posts: 130
- Joined: Tue Nov 29, 2016 2:59 pm
- cars: bf xr6 turbo
vs ss
vr clubsport - Location: Rockhampton
Re: 12p onto a 27c128??????
Thanks for those links. Champion. Will be getting my ordering stick out later and going shopping.