PCM questions regarding L67 Swap into VY

Holden/Delco Tuning. ALDL, OBD 1.5. Circa 1989 to 2004.
VYL67L03
Posts: 97
Joined: Sat Jan 18, 2020 8:34 am
cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
Location: Mid North Coast N.S.W

Re: PCM questions regarding L67 Swap into VY

Post by VYL67L03 »

I even tried after the heads were installed with the Ecotec harmonic balancer was still the same even tried it without connecting the supercharger belt lol
VYL67L03
Posts: 97
Joined: Sat Jan 18, 2020 8:34 am
cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
Location: Mid North Coast N.S.W

Re: PCM questions regarding L67 Swap into VY

Post by VYL67L03 »

Someone has told me it's probs the DFI module plate but was fine running the Ecotec
vs ss
Posts: 591
Joined: Thu Nov 03, 2011 7:57 pm
cars: hsv enhanced vs ss
vt xu6
fb holden
toyota landcruiser
vt ss s1
Location: perth wa

Re: PCM questions regarding L67 Swap into VY

Post by vs ss »

If it was running before I doubt it.
User avatar
antus
Site Admin
Posts: 8238
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: PCM questions regarding L67 Swap into VY

Post by antus »

What do the logs tell you?
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
VYL67L03
Posts: 97
Joined: Sat Jan 18, 2020 8:34 am
cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
Location: Mid North Coast N.S.W

Re: PCM questions regarding L67 Swap into VY

Post by VYL67L03 »

I haven't been logging anything I didn't think it would log anything until it actually started, So do you think I should start a log recording while trying to crank it ?
VYL67L03
Posts: 97
Joined: Sat Jan 18, 2020 8:34 am
cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
Location: Mid North Coast N.S.W

Re: PCM questions regarding L67 Swap into VY

Post by VYL67L03 »

In Tunerpro ? Thanks for the reply Antus
vs ss
Posts: 591
Joined: Thu Nov 03, 2011 7:57 pm
cars: hsv enhanced vs ss
vt xu6
fb holden
toyota landcruiser
vt ss s1
Location: perth wa

Re: PCM questions regarding L67 Swap into VY

Post by vs ss »

Yes in tunerpro. You can also see if it’s logged any fault codes.
By the way,did you cut any wires when you were making the harness fit the l67?
VYL67L03
Posts: 97
Joined: Sat Jan 18, 2020 8:34 am
cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
Location: Mid North Coast N.S.W

Re: PCM questions regarding L67 Swap into VY

Post by VYL67L03 »

Ah ok I'll do that later, Yes I had to extend the harness for 3 injectors, ground wire, & water temp sensor but is all wired up and connected, I don't get any check engine on the dash or anything
vs ss
Posts: 591
Joined: Thu Nov 03, 2011 7:57 pm
cars: hsv enhanced vs ss
vt xu6
fb holden
toyota landcruiser
vt ss s1
Location: perth wa

Re: PCM questions regarding L67 Swap into VY

Post by vs ss »

Ok just making certain nothing got mixed up in there.
VYL67L03
Posts: 97
Joined: Sat Jan 18, 2020 8:34 am
cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
Location: Mid North Coast N.S.W

Re: PCM questions regarding L67 Swap into VY

Post by VYL67L03 »

Should be all sweet, Will Tunerpro log all the cranking fuel data and injectors even though it's not starting ?
Post Reply