PCM questions regarding L67 Swap into VY
-
- Posts: 97
- Joined: Sat Jan 18, 2020 8:34 am
- cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
- Location: Mid North Coast N.S.W
Re: PCM questions regarding L67 Swap into VY
I even tried after the heads were installed with the Ecotec harmonic balancer was still the same even tried it without connecting the supercharger belt lol
-
- Posts: 97
- Joined: Sat Jan 18, 2020 8:34 am
- cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
- Location: Mid North Coast N.S.W
Re: PCM questions regarding L67 Swap into VY
Someone has told me it's probs the DFI module plate but was fine running the Ecotec
-
- Posts: 591
- Joined: Thu Nov 03, 2011 7:57 pm
- cars: hsv enhanced vs ss
vt xu6
fb holden
toyota landcruiser
vt ss s1 - Location: perth wa
Re: PCM questions regarding L67 Swap into VY
If it was running before I doubt it.
- antus
- Site Admin
- Posts: 8252
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: PCM questions regarding L67 Swap into VY
What do the logs tell you?
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 97
- Joined: Sat Jan 18, 2020 8:34 am
- cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
- Location: Mid North Coast N.S.W
Re: PCM questions regarding L67 Swap into VY
I haven't been logging anything I didn't think it would log anything until it actually started, So do you think I should start a log recording while trying to crank it ?
-
- Posts: 97
- Joined: Sat Jan 18, 2020 8:34 am
- cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
- Location: Mid North Coast N.S.W
Re: PCM questions regarding L67 Swap into VY
In Tunerpro ? Thanks for the reply Antus
-
- Posts: 591
- Joined: Thu Nov 03, 2011 7:57 pm
- cars: hsv enhanced vs ss
vt xu6
fb holden
toyota landcruiser
vt ss s1 - Location: perth wa
Re: PCM questions regarding L67 Swap into VY
Yes in tunerpro. You can also see if it’s logged any fault codes.
By the way,did you cut any wires when you were making the harness fit the l67?
By the way,did you cut any wires when you were making the harness fit the l67?
-
- Posts: 97
- Joined: Sat Jan 18, 2020 8:34 am
- cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
- Location: Mid North Coast N.S.W
Re: PCM questions regarding L67 Swap into VY
Ah ok I'll do that later, Yes I had to extend the harness for 3 injectors, ground wire, & water temp sensor but is all wired up and connected, I don't get any check engine on the dash or anything
-
- Posts: 591
- Joined: Thu Nov 03, 2011 7:57 pm
- cars: hsv enhanced vs ss
vt xu6
fb holden
toyota landcruiser
vt ss s1 - Location: perth wa
Re: PCM questions regarding L67 Swap into VY
Ok just making certain nothing got mixed up in there.
-
- Posts: 97
- Joined: Sat Jan 18, 2020 8:34 am
- cars: Vy Top Swapped L67 Supercharged Ecotec, Automatic soon to be Turboed
- Location: Mid North Coast N.S.W
Re: PCM questions regarding L67 Swap into VY
Should be all sweet, Will Tunerpro log all the cranking fuel data and injectors even though it's not starting ?