$11 Definition Info and XDF

[VL400]

The $11 code is used in VR V6 and V8 with automatic transmissions. It controls the 4L60E transmission along with the engine. The engine program is very similar to the VR $12 code, the main changes are for banked injection with a cam sensor. The V6 uses this while the V8 still uses batch injection where all 8 injectors are fired at once. The bins are 64k in size.

Bins
A list compiled by adrian of the various $11 bins and the code variant can be found here
Standard holden bins can be downloaded here

XDF For Editing In TunerPro
This is a fully featured TP4 XDF listing every single parameter available in the PCM, it uses categories and levels to try and make the XDF simpler to use. Its still a work in progress as the levels still need work along with some formatting of names. If you find any errors or would like to request a change please post here. The XDF works with the bins listed under variants 3, 4 and 5 of the post by adrian thats linked above.

$11B_V105.zip

26/09/2011 - Changed the inj/disp scalar to 4 decimal places

(39.41 KiB) Downloaded 1079 times

$11B_V104.zip

07/07/2011 - Fixed the high speed fuel cut, was RPM not KPH. Added descriptions to the fault flag headers

(39.39 KiB) Downloaded 564 times

$11B_V103.zip

19/07/2010 - Fixed a few items with signed and hex digits, added all the table bias corrections.

(35.2 KiB) Downloaded 696 times

Other XDFs can be found here


ADX for Logging In TunerPro 5
Can be downloaded here


ALDL Hardware
ALDL Interface


Real-Time Tuning In TunerPro 5
Real-Time modified bins can be found here which are used with an NVRAM. For reading and writing in realtime use Antus' TunerPro 5 plugin, or for reading and writing use the FlashTool

[yoda69]

Awesome work!!!
That is an unbelievably well defined xdf and layout.

[Tinker Profile]

WOW Excellent work mate.

[stevedarman Profile]

there are 4 lists for malf flags ,can some one explain these please
TRANS MALF MASK FLAGS, CEL ENABLE FLAGS, MALF FLAGS, TRANS MALF FLAG

another question
Run A/F Param - High Speed Fuel cutoff - Low Limit Is this road speed and units in kmh instead rpm?

[VL400]

Yep should have been KPH not RPM, fixed now

The flags are for processing the fault condition and then if the CEL should be displayed. There are two lots as the transmission code and engine code are kinda like two different systems, so there are two lots of flags.

[stevedarman Profile]

Can you give me a brief description on these codes?

TRANS MALF MASK FLAGS,
CEL ENABLE FLAGS,
MALF FLAGS,
TRANS MALF FLAG

[VL400]

The flags are for processing the fault condition and then if the CEL should be displayed. There are two lots as the transmission code and engine code are kinda like two different systems, so there are two lots of flags.

And In the updated XDF hover you mouse over the headings and it gives you a description. They just simply tell the PCM to process individual faults and if the fault is set to turn on the CEL.

[VX L67 Getrag Profile Website]

This XDF is really well defined but I've found a bin that has some stuff not defined, does anyone know what it is in these area's?

I thought anything before the start of the cal area was normally ram, but not sure?

There's also a hell of a lot of stuff after 8FFE of which I though that start getting into the programming area?

[VL400]

The $11 code is a little different and has program space before the cal, this is the reason the TP checksum does not work The items after 8FFE is also program space which starts at 0x9000.

[Heathmurray1986 Profile]

in looking at the setup everything is in MPH instead of KMH how do i change this?