Looking for a starter map, Kalmaker to $12P
Re: Looking for a starter map, Kalmaker to $12P
I use KALMAKER SP3 N03 XDFVersion 1.xdf
And KALMAKER_SP3_N03 TP5.adx
And KALMAKER_SP3_N03 TP5.adx
-
- Posts: 2883
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: Looking for a starter map, Kalmaker to $12P
I don't suppose you know what the changes are between 4C1 & 525 of the kalmaker file?
I'm pretty sure they're going to be some sort of EST or ESC but with that whole area being zero's it hard to tell where stuff starts & stops.
I'm pretty sure they're going to be some sort of EST or ESC but with that whole area being zero's it hard to tell where stuff starts & stops.
Re: Looking for a starter map, Kalmaker to $12P
Sorry no, i don't even know what/where that refers to in the map.
-
- Posts: 2883
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: Looking for a starter map, Kalmaker to $12P
This should be a good starting point, closest I can get with other items being unknown.
- Attachments
-
- OSE $12P V112 BLCF V8(try copy KAL tune).BIN
- (32 KiB) Downloaded 126 times
Re: Looking for a starter map, Kalmaker to $12P
cools, when i get home i'll have a look
So i havent actually uploaded anything $12P to the Kalamker (but i have been able to run the Kalamker XDF and mod the current map). What do i need to do to actually upload it the first time?
So i havent actually uploaded anything $12P to the Kalamker (but i have been able to run the Kalamker XDF and mod the current map). What do i need to do to actually upload it the first time?
-
- Posts: 2883
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: Looking for a starter map, Kalmaker to $12P
Thanks for posting in open forum like I mentioned in PM along with advice...
It's only a starting point so once you get it on a memcal will need to log & adjust as need as kalmaker has cyl vol which OSE $12p doesn't so I had to fudge injector rate for your injectors & the cyl vol too so it could be slightly off... but lets see how well it goes!
It's only a starting point so once you get it on a memcal will need to log & adjust as need as kalmaker has cyl vol which OSE $12p doesn't so I had to fudge injector rate for your injectors & the cyl vol too so it could be slightly off... but lets see how well it goes!
Re: Looking for a starter map, Kalmaker to $12P
Just having a look around the map and the Tip-in bump Spark seems to have a very random map. i dont even remember that in the Kalamker
is that a bad conversion from Kal to $12P?
Pic below
is that a bad conversion from Kal to $12P?
Pic below
- Attachments
-
- tip-in bump.PNG (57.96 KiB) Viewed 2234 times
- vlad01
- Posts: 7801
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Looking for a starter map, Kalmaker to $12P
I normally turn off RDSC which disables all the tip in bump stuff as it makes the engine rather unresponsive in my experience.
Never really looked at the tip in maps so can't tell you if it looks right or not.
Never really looked at the tip in maps so can't tell you if it looks right or not.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
- Posts: 2883
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: Looking for a starter map, Kalmaker to $12P
That table is untouched... just how the $12p BLCF file is!
Re: Looking for a starter map, Kalmaker to $12P
So what’s the map actually telling me?
Is it saying at 20% throttle at 1200rpm it’s going to knock 10.55 degrees of timing out?
Is it saying at 20% throttle at 1200rpm it’s going to knock 10.55 degrees of timing out?