Switch from code 59 to 12P

American Delco GM ECUs and PCMs, ALDL, OBD 1.5.
Posts: 46
Joined: Mon Dec 31, 2012 4:54 am
Location: LasVegastan

Re: Switch from code 59 to 12P

Postby 34blazer » Mon Feb 11, 2019 5:43 am

Also, I'm having trouble finding the store to look at the CnP ignition interface. Could you possibly point me in that direction? Thanks!
Image


Image

Site Admin
User avatar
Posts: 5525
Joined: Sat Feb 28, 2009 8:34 pm

Re: Switch from code 59 to 12P

Postby antus » Mon Feb 11, 2019 6:35 am

Yes you can edit the xdf. Im not sure what the cnp stuff that your looking for is. Can you explain?
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

Posts: 46
Joined: Mon Dec 31, 2012 4:54 am
Location: LasVegastan

Re: Switch from code 59 to 12P

Postby 34blazer » Mon Feb 11, 2019 7:08 am

I saw a thread that showed a ignition module interface to use a CNP set-up to replace the dizzy. I'll have to find it again
Image


Image

Posts: 46
Joined: Mon Dec 31, 2012 4:54 am
Location: LasVegastan

Re: Switch from code 59 to 12P

Postby 34blazer » Sat Feb 16, 2019 5:37 pm

OK, almost ready to swap.

1st hiccup. MAP sensor +5 Ref, do I need to steal that from the TPS ref? I don't see the pin labeled in the wiring guide.

2nd hiccup. The 7749 utilizes the VSS inputs directly and outputs a 2000ppm and 4000ppm signal. I completely forgot about the 165 may not have that ability. Is there a pulse divisor I can obtain just in case I cant find a DRAC that wont work with my transaxle ratio?

Thanks
Image


Image

Site Admin
User avatar
Posts: 5525
Joined: Sat Feb 28, 2009 8:34 pm

Re: Switch from code 59 to 12P

Postby antus » Sat Feb 16, 2019 5:52 pm

1: yes
2: hmm the original config of 12p is the vss to the dash, which divides by 4 (I think) then sends to the pcm. You may need a custom solution for that :( I dont think it'd hard to too hard to build one if you cant find anything pre-existing but it would be another project.
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

Posts: 46
Joined: Mon Dec 31, 2012 4:54 am
Location: LasVegastan

Re: Switch from code 59 to 12P

Postby 34blazer » Sun Feb 17, 2019 3:38 am

Im off to the junkyard now to rummage a DRAC/VSSB from an older chevy truck or GM car. Shouldn't be difficult to find one.

The Dakota digital speedo correction buffer will also work for those with the same issue.

Thanks Antus
Image


Image

User avatar
Posts: 9569
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: Switch from code 59 to 12P

Postby Holden202T » Mon Feb 18, 2019 12:49 pm

antus wrote:1: yes
2: hmm the original config of 12p is the vss to the dash, which divides by 4 (I think) then sends to the pcm. You may need a custom solution for that :( I dont think it'd hard to too hard to build one if you cant find anything pre-existing but it would be another project.

divide by 5

Previous

Return to US ALDL ECUs

Who is online

Users browsing this forum: No registered users and 2 guests