MadMax 355ci VN Calais - Tune 12P v112
Re: MadMax 355ci VN Calais
I just happened to stumble across a write-up about that red engine you just posted a photo of which you describe as "engineporn".
http://www.kanarisengines.com/announcem ... n-the-dyno
Yep. That's engineporn.
http://www.kanarisengines.com/announcem ... n-the-dyno
Yep. That's engineporn.
˙ʎɐqǝ ɟɟo pɹɐoqʎǝʞ ǝsǝuıɥɔ ɐ ƃuıʎnq ɹoɟ ʇɥƃıɹ ǝɯ sǝʌɹǝs
- madmaxisback
- Posts: 145
- Joined: Mon Nov 09, 2009 4:56 pm
- cars: VN Calais
VK Berlina - Location: Perth
Re: MadMax 355ci VN Calais
Agreed. I want a VN group A or Motec if I can. Stupid money but will do what is needed.immortality wrote:Be prepared to get bent over trying to find a genuine Grp A manifold. Someone really should re-manufacture these as they are still one of the best Holden EFI manifolds about.
Is Zok building the engine?
I am building the engine with the help of a few people here in WA. Machining, second and third set of eyes to get it spot on and save some . Hence why I am in no rush.
- madmaxisback
- Posts: 145
- Joined: Mon Nov 09, 2009 4:56 pm
- cars: VN Calais
VK Berlina - Location: Perth
Re: MadMax 355ci VN Calais
Got the Wideband cable run via bung behind brake booster then under heater box and under carpet to ECU. Controller is zipped just off gearbox half way up dip stick tube at the moment as I need the length in cable to get reading from both banks to find the leanest side.
Not sure if its too hot up there for controller?
Next step is wire in 6 pin Deutsch plug to earths, switch power and ECU pin. I am doing it this way so I can change out to a new wideband later pretty easily.
Pics to follow during the week if I get the chance.
Anyone used the LED function on the Spartan 2?
Not sure if its too hot up there for controller?
Next step is wire in 6 pin Deutsch plug to earths, switch power and ECU pin. I am doing it this way so I can change out to a new wideband later pretty easily.
Pics to follow during the week if I get the chance.
Anyone used the LED function on the Spartan 2?
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: MadMax 355ci VN Calais
I plan to connect it up to mine, but haven't done it yet!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- madmaxisback
- Posts: 145
- Joined: Mon Nov 09, 2009 4:56 pm
- cars: VN Calais
VK Berlina - Location: Perth
Re: MadMax 355ci VN Calais
Might give it a go with a switch with light in it.
More engine porn:
https://www.youtube.com/watch?v=UEOjUxZgocY
More engine porn:
https://www.youtube.com/watch?v=UEOjUxZgocY
- madmaxisback
- Posts: 145
- Joined: Mon Nov 09, 2009 4:56 pm
- cars: VN Calais
VK Berlina - Location: Perth
Re: MadMax 355ci VN Calais
UPDATE:
Hi guys,
Got my Spartan 2 wideband installed and working. Got the car to run and drive pretty good below 3000rpm, idles without any major hunt and seams like it might need less timing at idle but close. Stumbles and pings a little after 3k so more work needed.
Now questions for the experts:
What is the best way to run the AC condenser fan and my SPAL thermo off FAN1? (had it wired to switch but want to use Delco to run fans)
Will the circuit handle just wiring both together? Or will I need to add a relay etc. What happens when Air cond is turned on?
Or is there a way to use FAN2 (A3?) and where is the wiring to do this?
My car is Series 1 VN V8 with original harness in all places (no cuts or shuts)
Hope someone can help me so I can get her on the road for a bit more tuning and logging.
Hi guys,
Got my Spartan 2 wideband installed and working. Got the car to run and drive pretty good below 3000rpm, idles without any major hunt and seams like it might need less timing at idle but close. Stumbles and pings a little after 3k so more work needed.
Now questions for the experts:
What is the best way to run the AC condenser fan and my SPAL thermo off FAN1? (had it wired to switch but want to use Delco to run fans)
Will the circuit handle just wiring both together? Or will I need to add a relay etc. What happens when Air cond is turned on?
Or is there a way to use FAN2 (A3?) and where is the wiring to do this?
My car is Series 1 VN V8 with original harness in all places (no cuts or shuts)
Hope someone can help me so I can get her on the road for a bit more tuning and logging.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: MadMax 355ci VN Calais
i'd just leave the A/C condenser fan wiring as it is!
high speed fan output on the 808 should be C1, I dare say there is nothing there at the moment so you will need to add the required wiring and relay for it, if your fan that's on a switch is already a relay then just wire that to the C1 pin instead of the switch, then other than setting the on/off temperature you should be good to go.
high speed fan output on the 808 should be C1, I dare say there is nothing there at the moment so you will need to add the required wiring and relay for it, if your fan that's on a switch is already a relay then just wire that to the C1 pin instead of the switch, then other than setting the on/off temperature you should be good to go.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- madmaxisback
- Posts: 145
- Joined: Mon Nov 09, 2009 4:56 pm
- cars: VN Calais
VK Berlina - Location: Perth
Re: MadMax 355ci VN Calais
Awesome! So C1 has a blue and white wire coming out of it on my harness.Holden202T wrote:i'd just leave the A/C condenser fan wiring as it is!
high speed fan output on the 808 should be C1, I dare say there is nothing there at the moment so you will need to add the required wiring and relay for it, if your fan that's on a switch is already a relay then just wire that to the C1 pin instead of the switch, then other than setting the on/off temperature you should be good to go.
Relay under bonnet has this blue white wire with a orange with blue strip (eg AC fan wire or FAN1)???
- Attachments
-
- VNV6-4.gif~original.zip
- (115.92 KiB) Downloaded 345 times
Last edited by madmaxisback on Thu Oct 20, 2016 4:27 pm, edited 1 time in total.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: MadMax 355ci VN Calais
it must have the fan wiring in it then, that saves some work!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- madmaxisback
- Posts: 145
- Joined: Mon Nov 09, 2009 4:56 pm
- cars: VN Calais
VK Berlina - Location: Perth
Re: MadMax 355ci VN Calais
But this wiring is going to my A/C condenser fan currently.... Hence why I asked the question...Holden202T wrote:it must have the fan wiring in it then, that saves some work!
R37 is all there and Orange & blue is going to my AC fan... Can I run 2x fans off this circuit with 25amp fuse with ac fan pushing and thermo pulling and what will having ac on do to this setup?
These diagrams for VR V8 back this up too:
viewtopic.php?f=32&t=338#p3306
- Attachments
-
- Starting-charging-heating-cruise-st.jpg~original.zip
- (360.94 KiB) Downloaded 355 times