VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Conversion
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
Must have missed that page looks good
- JA2Z
- Posts: 76
- Joined: Tue Mar 08, 2016 9:59 am
- cars: - WH II 5.7L Statesman (daily)
- VT 5.0L Calais
- 1994 Ford Probe V6 DOHC
- 2007 Ford Focus TDCI 2.0 - Location: East Gippsland, Victoria
- Contact:
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
Prepping the Intake manifold for milling,
All the old dirty pits that came off the spare Intake: Dirty 2nd hand intake: All fresh:
Manky old stock VS V8 injectors: All parts vigorously cleaned with cleaner and elbow-grease:
All the old dirty pits that came off the spare Intake: Dirty 2nd hand intake: All fresh:
Manky old stock VS V8 injectors: All parts vigorously cleaned with cleaner and elbow-grease:
- JA2Z
- Posts: 76
- Joined: Tue Mar 08, 2016 9:59 am
- cars: - WH II 5.7L Statesman (daily)
- VT 5.0L Calais
- 1994 Ford Probe V6 DOHC
- 2007 Ford Focus TDCI 2.0 - Location: East Gippsland, Victoria
- Contact:
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
Quick question for the VR/S boys... how pivotal is the MAT sensor to the VS V8 PCM for fuelling calcs? Will I be able to run the motor without one connected, or is the IAT sensor not enough?
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
Very important, run it in the manifold not even in the intake pipe.
- JA2Z
- Posts: 76
- Joined: Tue Mar 08, 2016 9:59 am
- cars: - WH II 5.7L Statesman (daily)
- VT 5.0L Calais
- 1994 Ford Probe V6 DOHC
- 2007 Ford Focus TDCI 2.0 - Location: East Gippsland, Victoria
- Contact:
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
Hmmm... I have a sensor and bung for it in the VS manifold, but not in the currently installed VT stock Manifold.
Went to start the car with the VS PCM patched in..... No dice.... .... Not even sync with the NVRAM in TP5... ...or attempt at cranking ....must have some wiring gremlins. or a faulty 2nd hand PCM
Went to start the car with the VS PCM patched in..... No dice.... .... Not even sync with the NVRAM in TP5... ...or attempt at cranking ....must have some wiring gremlins. or a faulty 2nd hand PCM
Last edited by JA2Z on Sat Aug 12, 2017 6:51 pm, edited 1 time in total.
- JA2Z
- Posts: 76
- Joined: Tue Mar 08, 2016 9:59 am
- cars: - WH II 5.7L Statesman (daily)
- VT 5.0L Calais
- 1994 Ford Probe V6 DOHC
- 2007 Ford Focus TDCI 2.0 - Location: East Gippsland, Victoria
- Contact:
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
On all the Schematics and Pinouts I can find, I cannot see any reference to the Manifold Air Temp (MAT) Sensor... only Intake Air Temp (IAT) Sensor.... Am I mistaken in thinking the VS V8's had a temp sensor in the airbox? or is the IAT actually the MAT on the VS?
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
Vs series 1 & 2 had a MAT sensor in the intake manifold just like all previous models the series 3 vs and vt had intake temp sensor in the air box. Someone dropped a vs s3 5l into my vq at the time and fitted the IAT in the air box and it caused all sorts of issues with fuelling and timing so I ripped the manifold off drilled the little flat area in number 6 runner passengers side and fitted it there like the previous models and fixed a heap of issues I was having
- JA2Z
- Posts: 76
- Joined: Tue Mar 08, 2016 9:59 am
- cars: - WH II 5.7L Statesman (daily)
- VT 5.0L Calais
- 1994 Ford Probe V6 DOHC
- 2007 Ford Focus TDCI 2.0 - Location: East Gippsland, Victoria
- Contact:
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
Sweet! So IAT is MAT on VS s1-2.
I figured it was required, but I thought is was used in conjunction with the IAT... not instead of.... my bad.
Yeah.. VS series 3 is basically identical to my VT (MAF, etc.., etc..)
Cool, so I'll have to correct my IAT/MAT wiring for the VS loom, and see why I had no Comms to the VS PCM
I figured it was required, but I thought is was used in conjunction with the IAT... not instead of.... my bad.
Yeah.. VS series 3 is basically identical to my VT (MAF, etc.., etc..)
Cool, so I'll have to correct my IAT/MAT wiring for the VS loom, and see why I had no Comms to the VS PCM
- antus
- Site Admin
- Posts: 8250
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
MAT and IAT also come in to play a lot with timing calcs. Hot air will detonate a lot sooner than cold.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
- JA2Z
- Posts: 76
- Joined: Tue Mar 08, 2016 9:59 am
- cars: - WH II 5.7L Statesman (daily)
- VT 5.0L Calais
- 1994 Ford Probe V6 DOHC
- 2007 Ford Focus TDCI 2.0 - Location: East Gippsland, Victoria
- Contact:
Re: VT V8 304 MAF NVRAM -> VS V8 MAP NVRAM + M122 SC Convers
Hi Lads,
So.. had a spare minute to check the car.
[youtube]https://www.youtube.com/watch?v=2fO5tRxXve0[/youtube]
I have Wideband MTX-L analog voltage coming out of the MTX-L, all down the loom, at the PCM pin B10, but not showing up in TP5?
I have checked the B10 Pin Voltage meter and the Custom Gauge I setup for my Wideband in TP5, but no dice... Is there a flag to enable A5 and B10 as the inputs in Enhanced 1.00 ?
So.. had a spare minute to check the car.
[youtube]https://www.youtube.com/watch?v=2fO5tRxXve0[/youtube]
I have Wideband MTX-L analog voltage coming out of the MTX-L, all down the loom, at the PCM pin B10, but not showing up in TP5?
I have checked the B10 Pin Voltage meter and the Custom Gauge I setup for my Wideband in TP5, but no dice... Is there a flag to enable A5 and B10 as the inputs in Enhanced 1.00 ?
Last edited by JA2Z on Wed Sep 06, 2017 11:41 am, edited 1 time in total.