VR with l67 help needed
VR with l67 help needed
Hey guys long time i havnt been on here for.
Used to run a vp 5l turbo running on 12p with a vl400 i think hi speed coms board and using a moates ostrich 1.0
Now bought another project car a running vr ute v6 with 4l60e
Have bought a vt super 6 wreck and hoping to transplant the l67 into the vr.
Have done a heap of googling etc.
Going to keep the vr 4l60 and use the vr engine loom
My question is looks like im going to have to use 11p
Does anyone have a similar setup on a vr auto. Hoping to find a tune that can get me going then i can just street tune fine tune the fuel side on the street with my wideband.
Tune can be close to standard as ute will be a workhorse tow vehicle etc bit of fun.
To tune the vr will i be able to use my moates ostrich 1 ? Sorry been a long time since i used it last etc. Still have tuner pro etc on my pc and laptop
Any help will be appreciated
thanks
Used to run a vp 5l turbo running on 12p with a vl400 i think hi speed coms board and using a moates ostrich 1.0
Now bought another project car a running vr ute v6 with 4l60e
Have bought a vt super 6 wreck and hoping to transplant the l67 into the vr.
Have done a heap of googling etc.
Going to keep the vr 4l60 and use the vr engine loom
My question is looks like im going to have to use 11p
Does anyone have a similar setup on a vr auto. Hoping to find a tune that can get me going then i can just street tune fine tune the fuel side on the street with my wideband.
Tune can be close to standard as ute will be a workhorse tow vehicle etc bit of fun.
To tune the vr will i be able to use my moates ostrich 1 ? Sorry been a long time since i used it last etc. Still have tuner pro etc on my pc and laptop
Any help will be appreciated
thanks
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: VR with l67 help needed
Yeah ostrich and aldl cable for logging.
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: VR with l67 help needed
Hey delcowizzid
So for real time tuning on vr auto ecu i will have to purchase something like this
viewtopic.php?f=14&t=3612
Now to just find a tune
Sorry about all the questions has just been 7 plus years since i played with this stuff a lot has gone a blur
So for real time tuning on vr auto ecu i will have to purchase something like this
viewtopic.php?f=14&t=3612
Now to just find a tune
Sorry about all the questions has just been 7 plus years since i played with this stuff a lot has gone a blur
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: VR with l67 help needed
That board or your ostrich can real-time tune. And then cable for aldl logging or tuning with the nvram board viewtopic.php?f=14&t=3616
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: VR with l67 help needed
delcowizzid
thanks again for the help
Whats my chances of finding a tune already
Or will i have to start with a 11p vr auto v6 tune in 2 bar
put super 6 timing maps and fuel maps and injector data and go from there ?
thanks again for the help
Whats my chances of finding a tune already
Or will i have to start with a 11p vr auto v6 tune in 2 bar
put super 6 timing maps and fuel maps and injector data and go from there ?
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: VR with l67 help needed
wouldnt you be better off using the super 6 gearbox ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: VR with l67 help needed
By what i have read on the net
Cant use super 6 trans as different to vr wiring side
Easier to bolt up motor and use vr wiring and vr auto trans on super 6 motor
Cant use super 6 trans as different to vr wiring side
Easier to bolt up motor and use vr wiring and vr auto trans on super 6 motor
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: VR with l67 help needed
isnt that just the module on the side of the box ? which you shouldn't need ? as long as the round plug that goes into the box is the same it should work ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: VR with l67 help needed
No idea holden202T about the electrical side of the box.
But wouldnt the only benefit of the vt super 6 box be that its probably 1% stronger than my current vr 4l60e ?
Found another guy on here that done the mechanical side of the swap on a vr ute and he used vr 4l60e to l67 motor.
i pm him and he said he didnt do the tune was done by a shop with kalmaker
But wouldnt the only benefit of the vt super 6 box be that its probably 1% stronger than my current vr 4l60e ?
Found another guy on here that done the mechanical side of the swap on a vr ute and he used vr 4l60e to l67 motor.
i pm him and he said he didnt do the tune was done by a shop with kalmaker
Re: VR with l67 help needed
Anyone ?