How do I probe theought the data line to ecu to check?vlad01 wrote: ↑Tue Oct 22, 2024 4:10 pm I'd just check the ground pin is continuous to any good body ground as a sanity check, and probe through the data line to the ECU to make sure.
Other than checking the plugins in TP and settings, I don't know what else to suggest on the laptop side other than physically bad USB ports (common on HP laptops new out of the box which gets worse with use).
Tunerpro won't connect anymore
-
- Posts: 78
- Joined: Thu May 10, 2018 3:51 pm
- cars: vs caprice
Re: Tunerpro won't connect anymore
- antus
- Site Admin
- Posts: 8538
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Tunerpro won't connect anymore
Not with a multimeter. You can do it with a scope. But I think you are going down the wrong path.
If the basic checks are failing, most likely you've uploaded some data that is incompatible to the NVRAM (or shorted it out briefly or similar) and the operating system isnt running anymore, and thats why its not responding. If this is the case, you need an eeprom programmer, and you need to carefully pull the chip out the nvram carrier and re-write one of the stacked bins from the original zip file so that the contents can run the ECM again, and then it will start communicating again. There is no way to recover over ALDL if the operating system is not in a state where it can run the computer to provide ALDL anymore.
Essentially if you have power, and you can see the transmit light and nothing is coming back, and/or if the MAP light is going out the moment you key off instead of staying on for 2-4 seconds, and if you cant see any physical problem with the connections between comms and the ECM then this the case.
If the basic checks are failing, most likely you've uploaded some data that is incompatible to the NVRAM (or shorted it out briefly or similar) and the operating system isnt running anymore, and thats why its not responding. If this is the case, you need an eeprom programmer, and you need to carefully pull the chip out the nvram carrier and re-write one of the stacked bins from the original zip file so that the contents can run the ECM again, and then it will start communicating again. There is no way to recover over ALDL if the operating system is not in a state where it can run the computer to provide ALDL anymore.
Essentially if you have power, and you can see the transmit light and nothing is coming back, and/or if the MAP light is going out the moment you key off instead of staying on for 2-4 seconds, and if you cant see any physical problem with the connections between comms and the ECM then this the case.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 78
- Joined: Thu May 10, 2018 3:51 pm
- cars: vs caprice
Re: Tunerpro won't connect anymore
I have a spare nvram here. Put that in and wouldn't connect to that one either.
- antus
- Site Admin
- Posts: 8538
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Tunerpro won't connect anymore
Have you been able to confirm one way or the other if the nvram is running on the car? Have you tried the key off and watch the map_sw light to see if it goes straight out or not? This will tell you if you are looking at a problem with the program on the nvram, or the comms.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 78
- Joined: Thu May 10, 2018 3:51 pm
- cars: vs caprice
Re: Tunerpro won't connect anymore
No I haven't. Light stays on for 2 seconds after switching off.
- antus
- Site Admin
- Posts: 8538
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Tunerpro won't connect anymore
ok then. your nvram is right, you problem is between the ecm and the comms board like you suspected. Check the connections, if they look good by eye then even though its not common, its likely the transmit data line in ecm is dead. Even if you had some kind of computer problem you would see the RX light flash after the TX light when you hit detect hardware. The signal is going missing between the transmit side of the comms board, the cpu receive, the cpu transmit and the comms receive which triggers the RX light.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 78
- Joined: Thu May 10, 2018 3:51 pm
- cars: vs caprice
Re: Tunerpro won't connect anymore
Turns out to be the cable. New cable and all seems to be working
-
- Posts: 3552
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: Tunerpro won't connect anymore
What cable are you using?
-
- Posts: 78
- Joined: Thu May 10, 2018 3:51 pm
- cars: vs caprice
-
- Posts: 3552
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: Tunerpro won't connect anymore
Ahh. Never used one of those.