Delco OSE FlashTool V1.51
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: The FlashTool V1.36
The F1 device is the BCM, its possible the bus chatter is causing issues of not seeing a reply from it. Have a play with the silence timeout, I changed it to 15mS in the latest release as others said that works better, however 50mS works best for me on the test setup.
Can you use TP to log it using the ADX here .. https://pcmhacking.net/forums/viewtopic.php?f=10&t=725
What ALDL interface are you using??
Can you use TP to log it using the ADX here .. https://pcmhacking.net/forums/viewtopic.php?f=10&t=725
What ALDL interface are you using??
-
- Posts: 109
- Joined: Sat Mar 21, 2009 8:59 am
- cars: VX commodore
Re: The FlashTool V1.36
I am using a usb cable with aldl plug on the end it works with VR and VS.
I cant get tunerpro to connect
I have tried 50ms 100 ms even 15o ms with no luck
any more sujestions?
I cant get tunerpro to connect
I have tried 50ms 100 ms even 15o ms with no luck
any more sujestions?
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: The FlashTool V1.36
If TP and the flashtool wont connect it could be the cable, the later models are a little more critical due to a heap of bus chatter. Just incase you havnt, you must use the TP logging engine and not the OSEPlugin for VT and later.
Is your laptop reasonably spec'd? It takes more processing power due to the tight time scheduling.
Is your laptop reasonably spec'd? It takes more processing power due to the tight time scheduling.
-
- Posts: 109
- Joined: Sat Mar 21, 2009 8:59 am
- cars: VX commodore
Re: The FlashTool V1.36
what do you mean TP logging engine and not the OSEPlugin ?
lap top is new
lap top is new
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: The FlashTool V1.36
If you dont know what the plugin is then your prob not using it https://pcmhacking.net/forums/viewtopic.php?f=3&t=590
Re: The FlashTool V1.36
I think i might have one of those KDAC PCMs but I wont be able to check till I'm back in syd in Dec.
Re: The FlashTool V1.36
Thank you, we will waitejukated wrote:I think i might have one of those KDAC PCMs but I wont be able to check till I'm back in syd in Dec.
-
- Posts: 2886
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: The FlashTool V1.36
Not to seem rude or unappreciative, is there any chance we can make the tool just flash the corrected check sum on VX-VY PCM flash rather than having a complete re-write?
- antus
- Site Admin
- Posts: 8258
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: The FlashTool V1.36
With those flash chips you have to erase an entire block of flash, then re-send the whole chunk. Its not possible to just update a couple of bytes, and the pcms dont have enough ram to back up the whole block internally, so it needs to come from the pc again.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: The FlashTool V1.36
The main issue is you cant work out the checksum prior if writing just a cal - if writing an entire bin I could add a check prior to writing but thats really not going to help 90% of the time. The only alternative is to not write the checksum bytes (leave them erased as FF), write the cal, checksum it all and then fix the bytes. There are some drawbacks and the checksum fix was meant to be a temp solution until TP can handle it hence the current quick fix.