Couldnt really find a section for this..

[python]

WOW. There are some really talented people here. Just read this whole post start to finish. Most of it is another language to me. Keep up the awesome work.

[markagregory]

i have concoured this and worked it all out, managed to remove read, and write to my chip and then replace. editing ks, with no errors yet! level 3 dash upgrade now working in my vs, reading correct Ks for car. thanks to the help of this post.

my questions are -

1. wondering as i have a 3m clip on type connector that fits the chip and onto my programmer. would it harm or damage anything by programming chip while still on board ?, as i find the soldering the most challanging time consumbing part, dont want to kill/damage my trip computor system as it will be used in Ek sedan.

2. im looking to put - vs ecotec, level 3 BCM, electric windows, remote unlock, security, into my EK sedan, so would like to learn codes, functions, and to control/ understand the bcm. any help or leads greatly appreciated.

my aim if possible is to intergrate to ek dash with out radically changing the old school look of original EK dash, the vs speedo, gauges, trip computor strip. i realise i may need to recallabrate the vs gauges to read correct behind the ek facias [more research/learning]. and custom fit, make all electrical conections to each, i love a challange.

[jxx]

1. wondering as i have a 3m clip on type connector that fits the chip and onto my programmer. would it harm or damage anything by programming chip while still on board ?, as i find the soldering the most challanging time consumbing part, dont want to kill/damage my trip computor system as it will be used in Ek sedan.

no, the chip can't be reprogrammed while still on board (unless the serial port interface is worked out on the microcontroller, basically what the vdo unit does)

2. im looking to put - vs ecotec, level 3 BCM, electric windows, remote unlock, security, into my EK sedan, so would like to learn codes, functions, and to control/ understand the bcm. any help or leads greatly appreciated.

BCM is completely independent to the l3 trip computer

[VX L67 Getrag]

Sorry to move in on this, but I have been programming the VY-VZ eproms with a 3m clip & doing while still on the board with 100% success wouldn't it be the same as the VS eproms?

I have also read VT-VX eproms(with same 3m clip & GQ programmer) too posted in another thread here, but haven't yet try to reprogram these as I don't have enough info on them yet!

[jxx]

no it won't work, somewhere in the previous pages i mentioned i'd tried this, the extra circuitry on the board messes with the data to/from the chip.
reads all 0's and writes nothing.

[mark]

the 3 m clip seems to work fine, and i managed to read, erase, write, test in car, works , just to check i put different ks in and checked, it works with no errors every time. im happy that worked with no damage.

[creesy]

G'day guys my VN V8 standard dash broke so I got a replacement lvl cluster out of a VQ only problem is my car only had 171xxxkm on the clock and the replacement has 300000+km

I've read most of this thread but I really dont have the skill/tools to do it myself..

Can anyone help me out...of course I'm willing to pay for such a service

[The1]

nice, didn't realise it was still going this thread lol also there's calibration in the memcals vn-vs for the cluster, Litre/Hr INST Fuel Rate CAL = 82.32 and Amount of Fuel for 1/512 DU 1.43 Msec , not sure what 1/512 DU means

[jxx]

The1, guessing there's a flow cal number for when the vehicle isn't moving and just sitting idling to calc the fuel used... be interesting to to work out the datastream from the ecu to the trip computer, looks like it actually communicates a fair bit of info.

[Vpgts076]

HI GUYS,

LET ME JUST KEEP UP THE AWESOME WORK !!!!!!!!!!!!!!!!!!!!



This thread alone has got me into programming.............

I have Quite a few Q's for you.

1. Difference between VQ Series 1 & Series 2 Cluster.
* ABS Light only???

2. Differnece between V6 & V8.
* i know Tacho and there is a MOD.
* IS the trip different ie Fuel / 100KMS if so can it be modded?
* Temp gauge? Can it be moded if it is???

3. Can cluster speedo been Modded for different gear ratios? also can i create a 250KMS speedo and claibrate?

4. How can i mod RPg Gauge? want to have a custom 10,000 RPM in a factory style.

5. Below is the programer i purchased for odo,is this correct one??????
http://www.ebay.com.au/itm/190557900253 ... 1439.l2649

6. Does anybody have odo hex codes ina spread sheet?

Thanks Keep up the awesome work,...........
Daniel