dave V6 ek holden
-
- Posts: 1215
- Joined: Sun Mar 15, 2009 10:20 am
- cars: 2004 VYII Acclaim Wagon V6 Auto LPG/Petrol
2004 VYII Berlina sedan V6 Auto
2005 VZ Monaro CV8 manual - Location: Geelong, VIC
Re: dave V6 ek holden
Playing back your last log will be fine.
It shows manual all the way through that will be the issue. I'll have a look through the wiring diagrams and see if I can give you some areas to look.
yoda69
It shows manual all the way through that will be the issue. I'll have a look through the wiring diagrams and see if I can give you some areas to look.
yoda69
-
- Posts: 100
- Joined: Sat Aug 21, 2010 3:12 pm
- cars: EK holden running vn v6
- Location: Geelong
Re: dave V6 ek holden
bingo its stayed manual all the #@$##@ way ..
-
- Posts: 1215
- Joined: Sun Mar 15, 2009 10:20 am
- cars: 2004 VYII Acclaim Wagon V6 Auto LPG/Petrol
2004 VYII Berlina sedan V6 Auto
2005 VZ Monaro CV8 manual - Location: Geelong, VIC
Re: dave V6 ek holden
Have you hard wired the P/N switch in?
There should be grey wire from the P/N switch signal side to B10 on the ECU.
Yoda69
There should be grey wire from the P/N switch signal side to B10 on the ECU.
Yoda69
-
- Posts: 100
- Joined: Sat Aug 21, 2010 3:12 pm
- cars: EK holden running vn v6
- Location: Geelong
Re: dave V6 ek holden
yeah i have greg , other wise i dont think it will start as it wouldnt have a p or n signal ..
but ill check it out tomorrow .. i dont think i check the Over temp switch was going to correct terminal c7 i think .. not sure if that could be the answer
but ill check it out tomorrow .. i dont think i check the Over temp switch was going to correct terminal c7 i think .. not sure if that could be the answer
Re: dave V6 ek holden
yeah B10 needs to be hooked up to park/neutral switch and needs to actually change when the T-bar is put from neutral to drive. the ecm detects the change of state on this pin and sets the mode from manual to auto and enables the TCC function. this pin also allows the ecm to remember the IAC position in Drive so that the revs dont dop so much due to the sudden load.
-
- Posts: 1215
- Joined: Sun Mar 15, 2009 10:20 am
- cars: 2004 VYII Acclaim Wagon V6 Auto LPG/Petrol
2004 VYII Berlina sedan V6 Auto
2005 VZ Monaro CV8 manual - Location: Geelong, VIC
Re: dave V6 ek holden
If you have B10 connected to the wrong side of the P/N switch it will see a permanent ground and think it's a manual. When in park or neutral pin B10 should be grounded but when in reverse or drive should be open circuit.
Given yours is showing a manual all the time, I would suspect B10 is grounded.
yoda69
Given yours is showing a manual all the time, I would suspect B10 is grounded.
yoda69
-
- Posts: 100
- Joined: Sat Aug 21, 2010 3:12 pm
- cars: EK holden running vn v6
- Location: Geelong
Re: dave V6 ek holden
ok sweet sucesss after a little fiddling tp know it as auto and locks TCC when cruising
thanks Everyone
thanks Everyone
-
- Posts: 1215
- Joined: Sun Mar 15, 2009 10:20 am
- cars: 2004 VYII Acclaim Wagon V6 Auto LPG/Petrol
2004 VYII Berlina sedan V6 Auto
2005 VZ Monaro CV8 manual - Location: Geelong, VIC
Re: dave V6 ek holden
Good to hear, hopefully the the run to Bendigo goes well on the weekend.
yoda
yoda
-
- Posts: 100
- Joined: Sat Aug 21, 2010 3:12 pm
- cars: EK holden running vn v6
- Location: Geelong
Re: dave V6 ek holden
lol yeah last time i did the bendigo holden day the red motor dropped a rod just out side woodend finger crossed mind u if the weather is like today ill be staying at home
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: dave V6 ek holden
its allways the little things.good to see its all working fine now
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem