Vr V8 manual memcal
Vr V8 manual memcal
Hi, I'm in need of a memcal for my burnout car. It's a vr ute 383 stroker with twin tb manifold and a gt4294 turbo with a getrag 5 sp manual. I have lost the key so I will need VATS disabled. The ecu is 1618302 service number. I need a complete memcal not just a calibration as my tuned one has magicly learnt to remove itself and walk out of my ecu and cannot be located.
- antus
- Site Admin
- Posts: 8258
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Vr V8 manual memcal
have you got a 2 bar map sensor installed?
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: Vr V8 manual memcal
I'm actually not sure what the map sensor is as it was installed when I got the car. It looks standard. I did drive the car for 65 km and it went hard and smooth. Tho only identifying marks are 1/05
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Vr V8 manual memcal
it would probably be a good idea to multi meter it ... really need to know what it is for any custom tune to be even close to working
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Vr V8 manual memcal
Ok so I removed the sensor and had a look underneath. There is a sticker branded ACA but the part number is unreadable, how do I test it?
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Vr V8 manual memcal
Plug it back in and with the key on and measure the voltage of the middle pin. If its ~2.5V its a 2bar, approx 5V is a 1bar.
Re: Vr V8 manual memcal
It is reading 4.84v so must be a standard one, I will have to rectify this. I will buy a 2 bar ASAP.
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Vr V8 manual memcal
Is it using an auto or manual ecu? If its an auto PCM there then there is no 2 bar support freely available, will need to buy kalmaker.
If its a manual ECU 12P (https://pcmhacking.net/forums/viewtopic.php?f=27&t=356) supports 2 and 3 bar but you will still need to get someone to tune it.
If its a manual ECU 12P (https://pcmhacking.net/forums/viewtopic.php?f=27&t=356) supports 2 and 3 bar but you will still need to get someone to tune it.
Re: Vr V8 manual memcal
The ecu says 5.0 manual on it, I just purchased a 3 bar sensor.