Injector Flow Testing Data

Information and discussion of EFI hardware and specifications
Posts: 386
Joined: Wed Mar 04, 2009 8:52 pm

Re: Injector Flow Testing Data

Postby ejukated » Sat Oct 18, 2014 5:39 pm

do you think this is why the deadtime vs bpw table is 0 from factory?

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Sat Oct 18, 2014 5:47 pm

shouldn't be zero, all factory cals have there deadtimes.

Posts: 386
Joined: Wed Mar 04, 2009 8:52 pm

Re: Injector Flow Testing Data

Postby ejukated » Sat Oct 18, 2014 6:00 pm

hmm I might have defined it incorrectly.. will have to check. So the actual offset used for calculation is [cal]+0.5msec?

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Sat Oct 18, 2014 7:36 pm

yeh so for example VS V6 S/C has 0.50ms deadtime at 14.40volts in the factory tune, but it's actually 1.00ms as VS-VY code for some reason has 0.50ms built in. So if you get deadtime tables given to you from ID or Bosch or whoever, subtract 0.50ms from each value to use for deadtime tables in VS-VY, as far as i know 808 doesn't have any offset so straight data will be correct.

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Sat Dec 06, 2014 11:38 am

some new gear i scored cheap. HP bench PSU 0-60v 0-10amp and fluke frequency generator.
IMG_0640.JPG
IMG_0640.JPG (118.52 KiB) Viewed 2549 times


I did some deadtime testing on a new sheet ive made up using the new gear to reverify my results.
777-1.jpg
777-1.jpg (201.21 KiB) Viewed 2549 times

777-2.jpg
777-2.jpg (111.35 KiB) Viewed 2549 times

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Sat Dec 06, 2014 3:13 pm

Reference line setup on these ones for 3.5bar so you can see how linear they are. looks like i can tickle the low pulse adder table a bit more, pitty the table didn't go up higher to 6ms or so
Attachments
777-flowbench.jpg
777-flowbench.jpg (80.85 KiB) Viewed 2536 times
777-factory.jpg
777-factory.jpg (80.93 KiB) Viewed 2536 times

Posts: 44
Joined: Sun Apr 07, 2013 12:09 am

Re: Injector Flow Testing Data

Postby Xfirez51 » Mon Dec 08, 2014 1:47 am

The1,

I found something very similar in the .xdfs of the LT-5 cals. The Inj. Offset v BATT V uses the formula which "doubles" the OFFSET to account for both Opening and Closing times of injector. So the table displays total offset. I ran into this as I tried to tweak those values to accurately represent the ACCEL 21# injectors I am using rather than the stock Bosch. The Injector Offset table for Low PW does not do this.
Unfortunately, ACCEL never published the offsets for the their 150121 injectors altho they do now have values posted for 24# injectors and up.

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Mon Dec 08, 2014 8:11 am

yes VS-VY have a built in 0.5ms delay, so if using any other ecu that has standard "total" figure for battery tables you would have to add 0.5ms, it is a bit of pain but all PCM's and ECU's have there quirks.

Site Admin
User avatar
Posts: 5357
Joined: Sat Feb 28, 2009 8:34 pm

Re: Injector Flow Testing Data

Postby antus » Sat Dec 13, 2014 1:31 pm

Nice new kit. :D
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

User avatar
Posts: 4056
Joined: Mon Jan 04, 2010 10:23 am

Re: Injector Flow Testing Data

Postby The1 » Sat Dec 13, 2014 1:49 pm

it's getting there, it's about where i need it to be now for what my purposes are, obviously there is the consistent urge to tweak more! But i haven't had any time. I do want to grab a coolant temp sensor and fit it into the tank so i can log fuel temperature, also the pump is currently inside the tank, i will mount it external and perhaps make the tank a bit larger. I have been toying around with different ideas to make measuring the fluid more accurate but haven't come up anything solid yet, i am planing on testing one of these.

Chemical ETape liquid level sensor strip.
http://www.milonetech.com/Purchase_eTape.html

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 2 guests