PCMHacking Frequently Asked Questions (FAQ)

Holden/Delco Tuning. ALDL, OBD 1.5. Circa 1989 to 2004.
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by Holden202T »

I was going to post a thumbs up but I think biggvl has done enough for everyone ;)
immortality
Posts: 3416
Joined: Thu Apr 09, 2009 12:31 pm
cars: VH, VN, VS, VX

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by immortality »

Good work, that fairly much puts all the info together in easy to manage bites for any beginner :thumbup: (cause I think this thread could use just a couple more :D )
User avatar
Tazzi
Posts: 3422
Joined: Thu May 17, 2012 8:53 pm
cars: VE SS Ute
Location: WA
Contact:

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by Tazzi »

Biggvl wrote:
The1 wrote:added a new guide for chip burning, bin stacking and verifying data.
:thumbup: :thumbup: :thumbup: ......... :thumbup: Thankyou :D
:lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol:

And one for the road :thumbup:
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Image
User avatar
madmaxisback
Posts: 145
Joined: Mon Nov 09, 2009 4:56 pm
cars: VN Calais
VK Berlina
Location: Perth

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by madmaxisback »

Thank you everyone! :thumbup:
Proudy78
Posts: 2
Joined: Mon Sep 14, 2015 9:58 am
cars: Vc commodore with vl motor in it

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by Proudy78 »

Hi there I'm new . Is there a PCM hack plug in for a rb30 vl motor if anyone no s please
User avatar
antus
Site Admin
Posts: 8237
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by antus »

this question should be in its own topic, but heres a quick answer: rb30 stock ecu is not supported. You would need to swap in a delco. This is possible, but probably not a good first project. Once your familiar with the system and have a decent understanding of delco tuning, you could do this. You'd need to swap in high impedance injectors, add a MAT, swap the MAF for a MAP and do some magic to make a trigger system work. This would be either installing a position sensor on the front of the engine, or using the nissan CAS with one of VL400s custom ignition modules. You'd also need an auto TPS to get a 0-5v signal. Search these topics on this site to find more information, and if you are prepared to give it a go start up a new thread.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
VK_3800
Posts: 526
Joined: Sun Jul 04, 2010 3:15 pm
cars: SS Torana
Location: NZ

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by VK_3800 »

The factory ECU uses a standard 28 pin EPROM and there is a rough ADX around here somewhere for the RB30 tune so you can make some changes via Tunerpro with a standard chip burner. You would need to remove the original chip and put a socket on the board though.
Proudy78
Posts: 2
Joined: Mon Sep 14, 2015 9:58 am
cars: Vc commodore with vl motor in it

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by Proudy78 »

Thank you gents . I will have to have a good read and see witch way I will go .
Wade
Posts: 562
Joined: Mon Jul 11, 2016 6:29 am
cars: Vr 5.0 statesman vr exec 5.0 turbo vy clubsport

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by Wade »

How do I use kinjflow or ve by histogram ect in tunerpro
User avatar
antus
Site Admin
Posts: 8237
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: PCMHacking Frequently Asked Questions (FAQ)

Post by antus »

I put a link to the injector rate calculator near the top of the FAQ. It used to set the injector flow rate. Then the VE by histogram can be used to get a general idea of how to set up your VE, but note that it wont dial it in perfectly. Most people have more success by keeping spikes out of the VE table, logging with with a wideband. then observing trends in a given area. Then make changes to adjust that area and blend it in with the table around it to keep it reasonably smooth. Then repeat.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Post Reply