vz v6 e55 ecm vats reset
Re: vz v6 e55 ecm vats reset
The bcm links to pim then pim links to ecm pim writes immob code to ecm so then the immob code on the ecm wont match the holden data base for the vin of the ecu i tryed this on a bench harness i made thats why you have to do a resett on the ecm so basically it has no immob code stored on it then u put it in the vehicle and link using the immob code stored in pim of the vehicle you are repairing
- antus
- Site Admin
- Posts: 8253
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: vz v6 e55 ecm vats reset
Im talking about this type of stuff:
http://m.youtube.com/watch?v=kynXjan7O0Q
Ive not done it, could be wrong, but I thought it was the go for bosch pcm work. Certainly no silver bullet but i bet you reset one pcm, then melt the glue (much worse than in this vid on the e55) then read the flash, the repeat on another pcm to write and reset it back to unprogrammed state. Far from easy, but none the less....
http://m.youtube.com/watch?v=kynXjan7O0Q
Ive not done it, could be wrong, but I thought it was the go for bosch pcm work. Certainly no silver bullet but i bet you reset one pcm, then melt the glue (much worse than in this vid on the e55) then read the flash, the repeat on another pcm to write and reset it back to unprogrammed state. Far from easy, but none the less....
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: vz v6 e55 ecm vats reset
The1 wrote:nope
Thats the one
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: vz v6 e55 ecm vats reset
that top silicon die, the qg-4x comes with an adapter for that.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: vz v6 e55 ecm vats reset
really? mine didntvlad01 wrote:that top silicon die, the qg-4x comes with an adapter for that.
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: vz v6 e55 ecm vats reset
lol, was just kidding. No way anything on the human scale could connect to that lol.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: vz v6 e55 ecm vats reset
lol yeah I was thinking WTF. only way you could do something like that would be a BDM jig with very precise positioning.
- antus
- Site Admin
- Posts: 8253
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: vz v6 e55 ecm vats reset
It wouldnt surprise me if bdm or jtag was on the staggered connectors to the right of the main chip. Wouldn't be easy to connect but i'd be surprised if it wasn't possible.
- Attachments
-
- VZ ECU header.jpg (35.01 KiB) Viewed 4953 times
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: vz v6 e55 ecm vats reset
That would be one hell of a mission.
Im staring at it right now.. and to even get through the top layer of gel is seemingly impossible.
Im staring at it right now.. and to even get through the top layer of gel is seemingly impossible.
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726