Delco OSE FlashTool V1.51
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco FlashTool V1.51
you sure there is not some other settings wrong ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- antus
- Site Admin
- Posts: 8250
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Delco FlashTool V1.51
Various people (including myself) have had trouble getting them talking on the bench. Im still not sure what the fix is. Are you trying in car or on a bench? If on a bench try in car?
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
- hsv08
- Posts: 547
- Joined: Thu May 09, 2013 6:50 pm
- cars: (EX) VT SENATOR 355 STROKER
(EX) VT SS 304 MANUAL
NOW VX V6 HACK
Re: Delco FlashTool V1.51
Pretty sure. I've tried quite a few different combinations now.Holden202T wrote:you sure there is not some other settings wrong ?
- hsv08
- Posts: 547
- Joined: Thu May 09, 2013 6:50 pm
- cars: (EX) VT SENATOR 355 STROKER
(EX) VT SS 304 MANUAL
NOW VX V6 HACK
Re: Delco FlashTool V1.51
Yeah I have the flash PCM in my Vx that can't connect. I also built a bench setup and brought another PCM to try talk to but no go on that either. I made a thread on it a while ago.antus wrote:Various people (including myself) have had trouble getting them talking on the bench. Im still not sure what the fix is. Are you trying in car or on a bench? If on a bench try in car?
Retrying through flashtool in both setups was was last hope. I have tryed everything from disabling antivirus settings, different laptops with v151 on them bench and in car connects, nothing seems to want to connect with either PCM.
Though it will pick up through tuner pro as I can log. But flashtool won't pick it up.
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Delco FlashTool V1.51
If you can use TunerPro to connect to the bench PCM, close it and then try connecting with the flash tool. If it fails under the file menu choose "save detailed information" and post the file here.
The only time I have had issues with connecting to bench flash PCMs is if you don't have a switch on the ign wire. Powering both the constant and switched voltage at the same time sometimes the PCM wont boot. Need to power the constant and a few seconds later switch on the ign.
The only time I have had issues with connecting to bench flash PCMs is if you don't have a switch on the ign wire. Powering both the constant and switched voltage at the same time sometimes the PCM wont boot. Need to power the constant and a few seconds later switch on the ign.
- antus
- Site Admin
- Posts: 8250
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Delco FlashTool V1.51
That could be it. I probably did have ignition live.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
- hsv08
- Posts: 547
- Joined: Thu May 09, 2013 6:50 pm
- cars: (EX) VT SENATOR 355 STROKER
(EX) VT SS 304 MANUAL
NOW VX V6 HACK
Re: Delco FlashTool V1.51
Heres the detailed information I have can connected to the cars pcm via tunerpo and can log, but cant connect with flashtool.VL400 wrote:If you can use TunerPro to connect to the bench PCM, close it and then try connecting with the flash tool. If it fails under the file menu choose "save detailed information" and post the file here.
The only time I have had issues with connecting to bench flash PCMs is if you don't have a switch on the ign wire. Powering both the constant and switched voltage at the same time sometimes the PCM wont boot. Need to power the constant and a few seconds later switch on the ign.
The other pcm i have (VY) i have setup on the bench will connect via tunerpro (comes up ostrich IIv36.71.P but wont aquire any data) and obviuosly no connection with flashtool
I have triple checked all the wiring, The OBD2 plug i have connected to the bench harness didnt have a wire connected to pin 6 so i unpinned and used the ABS serial wire in its place (unsure why this didnt have a pin6?? Was from a VY)
Ignition wire is switched from 12v - D16
- hsv08
- Posts: 547
- Joined: Thu May 09, 2013 6:50 pm
- cars: (EX) VT SENATOR 355 STROKER
(EX) VT SS 304 MANUAL
NOW VX V6 HACK
Re: Delco FlashTool V1.51
I have tried hard wiring the ign to switch on with the 12v, i also have tried it switched (it was switched in the beginning then tried hardwired now back to switched)antus wrote:That could be it. I probably did have ignition live.
The OBD port has 4 wires connected.
pin 16---> C13
PIN 5---> NEG
PIN4----> NEG
PIN 6----> D9
I know there is a 12v constant in that plug but im not sure if that needs to be hooked up. im sure i have tryed with same results.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco FlashTool V1.51
if the diagram I am reading is correct, then C13 is serial data, so it shouldn't be pin 16, should be 9 ? Pin 6 to D9 is right, but I don't believe you need that for connecting, only for diagnostic test enable (jumper pin 5 and 6)
pretty sure you need
Pin 5 - GND
Pin 9 - Serial Data
Pin16 - 12v power.
and looking at the under dash plug, top row left 1->8 on the right, bottom row left 9->16 on the right.
pretty sure you need
Pin 5 - GND
Pin 9 - Serial Data
Pin16 - 12v power.
and looking at the under dash plug, top row left 1->8 on the right, bottom row left 9->16 on the right.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- hsv08
- Posts: 547
- Joined: Thu May 09, 2013 6:50 pm
- cars: (EX) VT SENATOR 355 STROKER
(EX) VT SS 304 MANUAL
NOW VX V6 HACK
Re: Delco FlashTool V1.51
i got my wiring from http://pcmhacking.net/forums/viewtopic. ... ring#p4323.Holden202T wrote:if the diagram I am reading is correct, then C13 is serial data, so it shouldn't be pin 16, should be 9 ? Pin 6 to D9 is right, but I don't believe you need that for connecting, only for diagnostic test enable (jumper pin 5 and 6)
pretty sure you need
Pin 5 - GND
Pin 9 - Serial Data
Pin16 - 12v power.
and looking at the under dash plug, top row left 1->8 on the right, bottom row left 9->16 on the right.
Have re wired the way you suggested. still nothing