Vs level3 fuel cal issue

Ecu Hardware Modifications
ben044
Posts: 71
Joined: Tue May 27, 2014 7:37 am
cars: vs 5l ute, hq 304 one tonner, ve sv6 wagon

Re: Vs level3 fuel cal issue

Post by ben044 »

Could i use a jaycar corrector to change the signal
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: Vs level3 fuel cal issue

Post by VL400 »

Need an adjustable PWM signal, not frequency like the speedo corrector does.

Haltech cant help? If its outputting something then surely it can be adjusted, but then again maybe not :lol:
ben044
Posts: 71
Joined: Tue May 27, 2014 7:37 am
cars: vs 5l ute, hq 304 one tonner, ve sv6 wagon

Re: Vs level3 fuel cal issue

Post by ben044 »

I could change flow rate in the haltech but then it would throw all my fuel rates out of wack. It was pretty close with my old injectors in but now that i have went bigger and changed tje rates in the haltech its thrown the dash out and the cal in the cluster needs to be 303 but it doesnt go that low.
ben044
Posts: 71
Joined: Tue May 27, 2014 7:37 am
cars: vs 5l ute, hq 304 one tonner, ve sv6 wagon

Re: Vs level3 fuel cal issue

Post by ben044 »

I jave found this. But they dont make the hand controller anymore
Attachments
Screenshot_20171105-182235.png
ben044
Posts: 71
Joined: Tue May 27, 2014 7:37 am
cars: vs 5l ute, hq 304 one tonner, ve sv6 wagon

Re: Vs level3 fuel cal issue

Post by ben044 »

Here is the pulse controller. They still make this bit but no way of controlling it
Attachments
Screenshot_20171105-175959.png
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: Vs level3 fuel cal issue

Post by VL400 »

ben044 wrote:I could change flow rate in the haltech but then it would throw all my fuel rates out of wack.
Was thinking more that the trip computer output of the haltech might be adjusted independently of the injector rate, like the delco does. A question for haltech, although based on a quick google it seems others have asked the question and never got a response.
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: Vs level3 fuel cal issue

Post by The1 »

VL400 wrote:VS fuel usage signal is a PWM signal, not 8192 baud data. VT was the first to use 8192 baud data for the trip computer.

The PCM accumulates the inj PW and outputs them in a PWM signal according to the calibration figure above that the1 noted, it specifies the amount of fuel per bit in teh PWM signal.
my bad, so yeh would need some kind of frequency adjuster or divider? then recal back on target in the cluster. easiest would be a cal adjustment in the ecu if it has one for it. It's obviously outputting the required PWM.
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: Vs level3 fuel cal issue

Post by VL400 »

Yeah seeing as there is something being output already, should be possible to adjust you would think.
ben044
Posts: 71
Joined: Tue May 27, 2014 7:37 am
cars: vs 5l ute, hq 304 one tonner, ve sv6 wagon

Re: Vs level3 fuel cal issue

Post by ben044 »

ok so i have been playing around with it and i'm getting closer to getting it, just trying to fine tune the duty cycle for the injector time
Post Reply