VT1 - How Much Rear Camber
- psyolent
- Posts: 1575
- Joined: Tue Apr 26, 2011 9:52 pm
- cars: VN S Pack
VX Berlina Series 1
XP Falcon ex Geelong Taxi
RN105 V8 Hilux
VT Series 1 Track Car
VT1 - How Much Rear Camber
So the VT which I want to peddle around a track given its an S1 has non abjustable rear camber. Sitting on SL springs the rear camber is alot (how much I don't know) but you can see its excessive.
As this thing is going to be on a track where you actually want *some* negative camber, is this a bad thing? ie: how much negative is too much?
ie this much
As this thing is going to be on a track where you actually want *some* negative camber, is this a bad thing? ie: how much negative is too much?
ie this much
Cheers,
Greg aka Sir Burnie Tanington
VX1 Berlina V6, VT1 Berlina V6 (Track), VN1 S V6, Hilux RN105 GMV8, Ford XP 170.
Greg aka Sir Burnie Tanington
VX1 Berlina V6, VT1 Berlina V6 (Track), VN1 S V6, Hilux RN105 GMV8, Ford XP 170.
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: VT1 - How Much Rear Camber
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
- Posts: 1833
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: VT1 - How Much Rear Camber
For fun track days minus 2 on the rear and minus 3 on the front.But daily driving you get moderate to serious tyre wear.
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: VT1 - How Much Rear Camber
For a race car when mileage isn't an issue some rear camber isn't a problem, if anything, desirable. The problem with the IRS is the change in camber/toe as the suspension moves through it's range of motion. Anything pre VX II (unless it's a HSV VT GTS) is more problematic as they don't have the extra toe link.
This covers the problem in detail http://www.whiteline.com.au/articles/WL ... e_link.pdf
This covers the problem in detail http://www.whiteline.com.au/articles/WL ... e_link.pdf
Re: VT1 - How Much Rear Camber
Interesting read there, basically the later rear ends sort out the bump steer and use less rear camber, there fore keeping the tyre tread at a more relevant angle to the road.
According to chemistry, alcohol is a solution...
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: VT1 - How Much Rear Camber
Fairly much.
The sad thing is (or so my understanding is) the original IRS system design had the toe links but Holden decided they weren't needed. My VS IRS has the ears on the hub castings where the original toe links would have been fitted.
Our VX II is running on Low springs (a touch lower than FE2 in the rear) has only very slight amount of rear camber but has no rear tyre wear issues.
The sad thing is (or so my understanding is) the original IRS system design had the toe links but Holden decided they weren't needed. My VS IRS has the ears on the hub castings where the original toe links would have been fitted.
Our VX II is running on Low springs (a touch lower than FE2 in the rear) has only very slight amount of rear camber but has no rear tyre wear issues.
- psyolent
- Posts: 1575
- Joined: Tue Apr 26, 2011 9:52 pm
- cars: VN S Pack
VX Berlina Series 1
XP Falcon ex Geelong Taxi
RN105 V8 Hilux
VT Series 1 Track Car
Re: VT1 - How Much Rear Camber
On the hub castings yes, but the mounts on the cradle no - the later VXII rear cradle is better. I have access to one so I'll grab it and swap it. The amount of camber in the rear is too excessive and won't be good.
Cheers,
Greg aka Sir Burnie Tanington
VX1 Berlina V6, VT1 Berlina V6 (Track), VN1 S V6, Hilux RN105 GMV8, Ford XP 170.
Greg aka Sir Burnie Tanington
VX1 Berlina V6, VT1 Berlina V6 (Track), VN1 S V6, Hilux RN105 GMV8, Ford XP 170.
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: VT1 - How Much Rear Camber
Yep, they saved on costs not welding on the brackets for the toe links...
It's a shame I can't change the rear subframe on the VS to the later spec unit![Sad :(](./images/smilies/icon_e_sad.gif)
It's a shame I can't change the rear subframe on the VS to the later spec unit
![Sad :(](./images/smilies/icon_e_sad.gif)
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: VT1 - How Much Rear Camber
I should add that someone makes a kit that allows you to cut off the original subframe swing arm mounts and weld on new ones as well as modify the arms to help improve the geometry. There is a thread on the Commodores Plus forum that has pics of the mods.
- psyolent
- Posts: 1575
- Joined: Tue Apr 26, 2011 9:52 pm
- cars: VN S Pack
VX Berlina Series 1
XP Falcon ex Geelong Taxi
RN105 V8 Hilux
VT Series 1 Track Car
Re: VT1 - How Much Rear Camber
immo - http://www.commodoresplus.com.au/forums ... ered-cars/
Interesting indeed.
Interesting indeed.
Cheers,
Greg aka Sir Burnie Tanington
VX1 Berlina V6, VT1 Berlina V6 (Track), VN1 S V6, Hilux RN105 GMV8, Ford XP 170.
Greg aka Sir Burnie Tanington
VX1 Berlina V6, VT1 Berlina V6 (Track), VN1 S V6, Hilux RN105 GMV8, Ford XP 170.