vz v6 e55 ecm vats reset
Re: vz v6 e55 ecm vats reset
I have read somewhere that when these get 'reconditioned' they immerse the whole board in a type of white spirit to dissolve the gel.. When fitting J3 chips to Ford ecu's I use brake cleaner to dissolve the goo..
According to chemistry, alcohol is a solution...
Re: vz v6 e55 ecm vats reset
Bugga that, not worth the time and effort I think.
Easier to just pickup some second hand ones, verify they are working and then reset them.
Easier to just pickup some second hand ones, verify they are working and then reset them.
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: vz v6 e55 ecm vats reset
Do you mean in the car? If so, that is impossibly hard to do, most VZ's end up in the wrecking yards cos they are fucked/smashed, very hard to find one around here at a wreckers in startable condition.
I have a large amount of second hand ecu's that are useless because I/we can't 'delink' them...
I have a large amount of second hand ecu's that are useless because I/we can't 'delink' them...
According to chemistry, alcohol is a solution...
Re: vz v6 e55 ecm vats reset
From memory you only need the code, goto reset ecu in tech2 and use old code
-
- Posts: 2882
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: vz v6 e55 ecm vats reset
Yeah there's plenty I've reset just on the bench & using snap-on tool, so long as you use the right code!
Re: vz v6 e55 ecm vats reset
Haha, nah nah. I just pickup any, no idea if there working the the first place. Probably 1 in 20 are faulty.Biggvl wrote:Do you mean in the car? If so, that is impossibly hard to do, most VZ's end up in the wrecking yards cos they are fucked/smashed, very hard to find one around here at a wreckers in startable condition.
I have a large amount of second hand ecu's that are useless because I/we can't 'delink' them...
I check them by ensuring they communicate happily over the canbus. Faulty ones normally have some intermittent troubles with communication.
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: vz v6 e55 ecm vats reset
Found this on trionictuning.com
me9.6 bdm
me9.6 bdm
- Attachments
-
- ME9.6 BDM-Connection.JPG (123.58 KiB) Viewed 3155 times
Last edited by mattyjf01 on Thu Sep 26, 2019 10:28 pm, edited 1 time in total.
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: vz v6 e55 ecm vats reset
Open source software that could work with some modification on bosch me9.6
https://github.com/mattiasclaesson/Trionic
https://github.com/mattiasclaesson/Trionic
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203