5l knock sensor
5l knock sensor
Hello guys,
I have a wierd issue my memcal does not have a knock filter board connected and the knock sensor settings disabled in the tune. Since it's disabled I decided to remove the knock sensor and plug but I get code 42, and the tacho bounces all over the place..when I plug it in car runs perfect so confused
I have a wierd issue my memcal does not have a knock filter board connected and the knock sensor settings disabled in the tune. Since it's disabled I decided to remove the knock sensor and plug but I get code 42, and the tacho bounces all over the place..when I plug it in car runs perfect so confused
- antus
- Site Admin
- Posts: 8252
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: 5l knock sensor
Sounds like a wiring issue. 42 is a problem on the EST circuit to the ignition module. I'd be checking the wires go where you think they go, between the ignition module and the pcm, and the knock sensor and the pcm. Maybe someone has wired a power connection through the sensor in error and gotten away with it until now, or similar.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: 5l knock sensor
Thanks Antus.
I have check the wiring against my diagrams and everything is correct the knock sensor wire was connected to B11. With it unplugged the car get the engine light even though in the mental it was set to never work lol
I have check the wiring against my diagrams and everything is correct the knock sensor wire was connected to B11. With it unplugged the car get the engine light even though in the mental it was set to never work lol
Last edited by vn_ss_cm on Wed Oct 02, 2019 8:08 pm, edited 1 time in total.
-
- Posts: 1215
- Joined: Sun Mar 15, 2009 10:20 am
- cars: 2004 VYII Acclaim Wagon V6 Auto LPG/Petrol
2004 VYII Berlina sedan V6 Auto
2005 VZ Monaro CV8 manual - Location: Geelong, VIC
Re: 5l knock sensor
Seems a little strange, wondering if it maybe an error in the xdf?
What bin and xdf are you using?
What bin and xdf are you using?
Re: 5l knock sensor
It's a VP clubsport bin and $DB
Re: 5l knock sensor
Hello Guys
Sorted out the issue the tune had knock enabled....question is it possible to hook up a resistor to trick the ecu into thinking a knock sensor is connected?
Sorted out the issue the tune had knock enabled....question is it possible to hook up a resistor to trick the ecu into thinking a knock sensor is connected?
- antus
- Site Admin
- Posts: 8252
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: 5l knock sensor
I assume that would be possible, but the harder part is the knock filter. if you get that wrong you get false knock, and if you have the v8 filter, you might as well put a sensor on it, or sell it and disable the sensor in the tune.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: 5l knock sensor
ah I see the thing is it has no knock filter board.....the tune has the knock sensor disabled by adjusting the ESC parameter but the code 43 is still active so when the car starts it goes into limp mode and comes up with - knock sensor code (43
would a resistor in its place trick the memcal? if so what resistance?
would a resistor in its place trick the memcal? if so what resistance?
-
- Posts: 1833
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: 5l knock sensor
3300 to 4500 ohms.
- antus
- Site Admin
- Posts: 8252
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: 5l knock sensor
I'll be interesting to see if that works. without the knock board I suspect it work. I think you also need to toggle the CEL flag for code 43 in the tune to stop it lighting the CEL rather than a hardware mod. Perhaps that flag isnt defined for DB and thats your problem.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396