My submerge import "traded for vn wagon"
-
delcowizzid
- Posts: 5709
- Joined: Sat Feb 28, 2009 10:38 am
- Yahoo Messenger: [email protected]
- Location: Wellington NZ
Re: My submerge import "traded for vn wagon"
made it home done over 1000km now still going 
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
delcowizzid
- Posts: 5709
- Joined: Sat Feb 28, 2009 10:38 am
- Yahoo Messenger: [email protected]
- Location: Wellington NZ
Re: My submerge import "traded for vn wagon"
http://www.youtube.com/watch?v=g9SpG1IRbvQ small shitty video
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
Holden202T
- Posts: 10435
- Joined: Sat Feb 28, 2009 11:05 am
- Location: Tenambit, NSW
Re: My submerge import "traded for vn wagon"
nice camera work
next video will have to be doughnuts with the camera on the roof or something!!
next video will have to be doughnuts with the camera on the roof or something!!
No matter what the question is, the answer is always more horsepower! 
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread

Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
-
delcowizzid
- Posts: 5709
- Joined: Sat Feb 28, 2009 10:38 am
- Yahoo Messenger: [email protected]
- Location: Wellington NZ
Re: My submerge import "traded for vn wagon"
haha shes hard to drive on boost while holding the camera with one had so had to hold the wheel and camera LOL anyone suffer motion sickness yet LOL might use the 100mph tape and stick it on the window next time
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
yoda69
- Posts: 1226
- Joined: Sun Mar 15, 2009 12:20 am
- cars: 2004 VYII Acclaim Wagon V6 Auto LPG/Petrol
2004 VYII Berlina sedan V6 Auto
2005 VZ Monaro CV8 manual - Location: Geelong, VIC
Re: My submerge import "traded for vn wagon"
LOL's.
With those lean angles thought it was strapped to a motorbike.
With those lean angles thought it was strapped to a motorbike.
-
antus
- Site Admin
- Posts: 10013
- Joined: Sat Feb 28, 2009 10:34 am
- cars: TX Gemini 2L Twincam 8psi
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Subaru WRX 2007
Re: My submerge import "traded for vn wagon"
haha nice naw_7s 
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
delcowizzid
- Posts: 5709
- Joined: Sat Feb 28, 2009 10:38 am
- Yahoo Messenger: [email protected]
- Location: Wellington NZ
Re: My submerge import "traded for vn wagon"
yip shes at home on the dash but now i have my new one it may have to get mounted in the car properly instead of wiring through the doors etc
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
Jayme
- Posts: 2585
- Joined: Sat Feb 28, 2009 10:59 pm
- Location: North Coast, NSW
Re: My submerge import "traded for vn wagon"
I ran my wiring down thru the bung hole in the passenger floor
-
delcowizzid
- Posts: 5709
- Joined: Sat Feb 28, 2009 10:38 am
- Yahoo Messenger: [email protected]
- Location: Wellington NZ
Re: My submerge import "traded for vn wagon"
went 10psi today 2nd gear didnt stand a change of shifting anywhere near fast LOL slipped like all hell time for the corvette servo and shit before going that high again
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
Holden202T
- Posts: 10435
- Joined: Sat Feb 28, 2009 11:05 am
- Location: Tenambit, NSW
Re: My submerge import "traded for vn wagon"
get a shift kit for it too, that poor old box 
No matter what the question is, the answer is always more horsepower! 
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread

Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread