Page 13 of 345
Re: Vlad's VP executive (full restro)
Posted: Mon Jun 17, 2013 10:23 pm
by vlad01
I got my red VN s1 with T5, can you see it?
- IMG_0620_zps7a9e680d.jpg (117.41 KiB) Viewed 5284 times
Re: Vlad's VP executive (full restro)
Posted: Mon Jun 17, 2013 10:29 pm
by vs ss
Na but I can see where you changed gears
Re: Vlad's VP executive (full restro)
Posted: Mon Jun 17, 2013 11:05 pm
by vlad01
This engine is insane! so much power its hard to believe its stock. Hopefully I might get some good money for it.
Re: Vlad's VP executive (full restro)
Posted: Tue Jun 18, 2013 8:01 am
by VK_3800
Yeah the S1 manuals are pretty good down low, its all over by 4000rpm though!
edit: is it on the right in the trees?
Re: Vlad's VP executive (full restro)
Posted: Tue Jun 18, 2013 7:54 pm
by vlad01
No, vs ss got it in one. You can see where its been though
Re: Vlad's VP executive (full restro)
Posted: Tue Jun 18, 2013 9:48 pm
by Holden202T
bloody hoon
Re: Vlad's VP executive (full restro)
Posted: Tue Jun 18, 2013 10:34 pm
by vlad01
I don't hoon, i just drive to what the car is capable of.
its called utilizing.
Re: Vlad's VP executive (full restro)
Posted: Tue Jun 18, 2013 10:51 pm
by Holden202T
I'm hearing ya, do that every time I drive my Gemini
Re: Vlad's VP executive (full restro)
Posted: Sun Jun 23, 2013 10:40 pm
by vlad01
finished cleaning and scraping all the seam sealer from the boot underside, started on the top today.
- IMG_0636_zps10f30b43.jpg (65.56 KiB) Viewed 5284 times
Pulled the dash out of the parts berlina, the dash isn't too bad and is already the correct color that I want, so I am stashing it for now
- IMG_0638_zpse7d6e378.jpg (100.89 KiB) Viewed 5284 times
And as I suspected the VP remotes match to the anti theft module.
- IMG_0639_zps41a3b79a.jpg (60.07 KiB) Viewed 5284 times
Re: Vlad's VP executive (full restro)
Posted: Sat Jun 29, 2013 6:35 pm
by vlad01
More work today!
tools
- IMG_0646_zpsbdec3b9d.jpg (68.32 KiB) Viewed 5284 times
boot semi preped. Will do a complete sand when I am ready to start doing primer come spring.
- IMG_0643_zpsb2568cb0.jpg (50.33 KiB) Viewed 5284 times
Had a go at blocking the existing factory primer. its super easy to sand and sould save me a lot of work and not requiring as much new primer.
- IMG_0644_zps6145d8ae.jpg (61.75 KiB) Viewed 5284 times
After some few hours playing around with the dollys and hammer I got this part pretty good, filed it with the panel file I bought to check flatness and seem pretty damn close, did a bit more work after this pic was taken.
- IMG_0649_zpse6eeed2b.jpg (63.65 KiB) Viewed 5284 times
some primer to see the result, looked pretty straight.
- IMG_0650_zps5ed101e3.jpg (78.75 KiB) Viewed 5284 times