Re: V6 ability for pcm hammer.
Posted: Mon Jan 27, 2020 1:43 pm
My PCM turned out to be DOA 
Ive ordered another but back to waiting...
Ive ordered another but back to waiting...pcmhacking.net
Electronic Fuel Injection - Developement & Tuning
https://pcmhacking.net/forums/
V6 ability for pcm hammer.
Page 15 of 24
Re: V6 ability for pcm hammer.
Posted: Mon Jan 27, 2020 1:47 pm
they refund it or you get ripped off
Re: V6 ability for pcm hammer.
Posted: Mon Jan 27, 2020 1:52 pm
Not sure, it could have been my P01/P59 loom that damaged it, I didnt realise when I first hooked it up that I had a non-standard pin used for B+ that worked fine on the other pcms, but is used for something else on the p04. 
Going to give them the benefit of the doubt. International shipping from the US is a killer (more than the PCMs)
Going to give them the benefit of the doubt. International shipping from the US is a killer (more than the PCMs) Re: V6 ability for pcm hammer.
Posted: Tue Jan 28, 2020 12:00 pm
yeah my test harness uses 18,19 for power 59 for data and 60 for ground
its good for p01/p59 and p04
its good for p01/p59 and p04
Re: V6 ability for pcm hammer.
Posted: Tue Jan 28, 2020 1:14 pm
My bench harness:
Pin 19, Switched Battery (ignition)
Pin 20, 12V Battery
Pin 58, Data
Pin 60, Ground
12v is fused.
https://github.com/LegacyNsfw/PcmHacks/ ... h-Flashing
I'll check the V6 wiring diagrams before I use it...
Pin 19, Switched Battery (ignition)
Pin 20, 12V Battery
Pin 58, Data
Pin 60, Ground
12v is fused.
https://github.com/LegacyNsfw/PcmHacks/ ... h-Flashing
I'll check the V6 wiring diagrams before I use it...
Re: V6 ability for pcm hammer.
Posted: Tue Jan 28, 2020 1:41 pm
Same pinout I have, havent tried a P04 though.Vampyre wrote:yeah my test harness uses 18,19 for power 59 for data and 60 for ground
its good for p01/p59 and p04
Is there a few part numbers for the _04 that we can search/look for? Happy pickup one also.
Re: V6 ability for pcm hammer.
Posted: Tue Jan 28, 2020 1:52 pm
That is the standard pinouts and is correct. I built my desk loom way back, probably 8 years ago, I just expected it to work since its worked all this time on p01/p59. Its not an ongoing problem, just the kind of thing that burns you every so often doing this type of stuff.
Re: V6 ability for pcm hammer.
Posted: Tue Jan 28, 2020 3:23 pm
I bench flash tunes for swaps all the time so it gets almost daily use, its good for any pcm that has a blue connector any 0411 look alike pcm
Re: V6 ability for pcm hammer.
Posted: Tue Jan 28, 2020 3:24 pm
Hi all,Tazzi wrote:Same pinout I have, havent tried a P04 though.Vampyre wrote:yeah my test harness uses 18,19 for power 59 for data and 60 for ground
its good for p01/p59 and p04
Is there a few part numbers for the _04 that we can search/look for? Happy pickup one also.
Tazzi, both the 2004 Olds Alero I had, and the 2005 Chevy Venture that I have, use the LA1 3400 V6. They both use the same PCM:
Mike
Re: V6 ability for pcm hammer.
Posted: Thu Jan 30, 2020 9:45 am
Thanks Mike!
Just bought one now (https://www.ebay.com/itm/184108101526)
Come with some connectors too if anyone needs some here in Aus.
Just bought one now (https://www.ebay.com/itm/184108101526)
Come with some connectors too if anyone needs some here in Aus.