Got engine bay done also
Before pictures after
253 V8 carby selection
-
Madmatt2006
- Posts: 373
- Joined: Fri Aug 31, 2018 4:48 am
- cars: VZ SVZ Commodore
VH Commodore
JZZ30 Soarer GTT - Location: Katandra West
Re: 253 V8 carby selection
I'll take it to super balance they do this type of work. I have a Soarer auto tailshaft some where also. I changed the the bushing today is that in far enough?
had big plans of getting the gearbox on today but the thrust bearing they sent with clutch kit won't fit it's to small!
Got engine bay done also
Before pictures after
Got engine bay done also
Before pictures after
You do not have the required permissions to view the files attached to this post.
-
'quipt4it
- Posts: 675
- Joined: Sun Oct 28, 2012 2:57 am
Re: 253 V8 carby selection
.
Last edited by 'quipt4it on Fri Aug 27, 2021 3:21 pm, edited 1 time in total.
-
Madmatt2006
- Posts: 373
- Joined: Fri Aug 31, 2018 4:48 am
- cars: VZ SVZ Commodore
VH Commodore
JZZ30 Soarer GTT - Location: Katandra West
Re: 253 V8 carby selection
From the ad for the clutch kit https://www.ebay.com.au/itm/360101787646 the thrust bearing should fit my gearbox hey? The hole in the bearing is to small.
-
'quipt4it
- Posts: 675
- Joined: Sun Oct 28, 2012 2:57 am
Re: 253 V8 carby selection
.
Last edited by 'quipt4it on Fri Aug 27, 2021 3:21 pm, edited 1 time in total.
-
Madmatt2006
- Posts: 373
- Joined: Fri Aug 31, 2018 4:48 am
- cars: VZ SVZ Commodore
VH Commodore
JZZ30 Soarer GTT - Location: Katandra West
Re: 253 V8 carby selection
ah ha they mention in red!
"important please note :
Thrust bearing supplied in this kit is an early Holden type
GSB-222 As pictured"
wrong one!
"important please note :
Thrust bearing supplied in this kit is an early Holden type
GSB-222 As pictured"
wrong one!
-
Madmatt2006
- Posts: 373
- Joined: Fri Aug 31, 2018 4:48 am
- cars: VZ SVZ Commodore
VH Commodore
JZZ30 Soarer GTT - Location: Katandra West
Re: 253 V8 carby selection
I'm confused which thrust bearing will suit Delow fork and gearbox
-
'quipt4it
- Posts: 675
- Joined: Sun Oct 28, 2012 2:57 am
Re: 253 V8 carby selection
.
Last edited by 'quipt4it on Fri Aug 27, 2021 3:22 pm, edited 2 times in total.
-
Madmatt2006
- Posts: 373
- Joined: Fri Aug 31, 2018 4:48 am
- cars: VZ SVZ Commodore
VH Commodore
JZZ30 Soarer GTT - Location: Katandra West
Re: 253 V8 carby selection
I guess Dellow would have one since all of the conversion kit is from them 
-
'quipt4it
- Posts: 675
- Joined: Sun Oct 28, 2012 2:57 am
Re: 253 V8 carby selection
.
Last edited by 'quipt4it on Fri Aug 27, 2021 3:22 pm, edited 1 time in total.
-
Madmatt2006
- Posts: 373
- Joined: Fri Aug 31, 2018 4:48 am
- cars: VZ SVZ Commodore
VH Commodore
JZZ30 Soarer GTT - Location: Katandra West
Re: 253 V8 carby selection
I stumbled across the one you mentioned on eBay it would have to be the right one for sure? it's expensive 
. With the thrust bearing and Dellow fork is there a clip to attach it? like there was on the fork and thrust bearing off the supra below.
. With the thrust bearing and Dellow fork is there a clip to attach it? like there was on the fork and thrust bearing off the supra below.
You do not have the required permissions to view the files attached to this post.