Page 3 of 4
Re: 0411 running a 2.5L Jeep engine
Posted: Sat Jan 21, 2023 11:31 am
by RADustin
check your timing with an index-able light. once you know the offset you can dial it in within the pcm. most XDF files have the offset mapped. use a scan tool to lock the timing.
I've run a few small blocks and big blocks on P01/P59....and recently took my friends Buick 215 for a ride that is P01 and DBW. I love these PCMs.
Re: 0411 running a 2.5L Jeep engine
Posted: Sat Jan 21, 2023 11:55 am
by Thorwon
syntaxterror wrote:Thorwon, what changes did you make in the bin to run on 4 coils?
All I've done is turn off the DTCs for the coils and injectors off. It still needs tuning.
I haven't worked on it in a while, life happens. Sometimes good sometimes not so good.
When I get the opportunity to do more on it, I'll post it.
Re: 0411 running a 2.5L Jeep engine
Posted: Sun Jan 22, 2023 1:14 am
by syntaxterror
Thank you, I am playing with a 2.5 ironduke and the 0411 sounds like option.
Re: 0411 running a 2.5L Jeep engine
Posted: Sun Jan 22, 2023 9:41 am
by syntaxterror
Thorwon. I remember reading that GM and jeep iac use the same connector but have a different pin out.
Re: 0411 running a 2.5L Jeep engine
Posted: Sun Jan 22, 2023 2:46 pm
by Chuff
Thorwon,
Will you be running this on a MAF tune or a MAP tune?
Thanks.
Re: 0411 running a 2.5L Jeep engine
Posted: Mon Jan 23, 2023 12:00 am
by Thorwon
Chuff wrote:Thorwon,
Will you be running this on a MAF tune or a MAP tune?
Thanks.
I am going to try and run it on a map tune. I still reading how to set-up everything.
This is something I've never done.
We'll see how it goes when I get the time to work on it.
Re: 0411 running a 2.5L Jeep engine
Posted: Thu Feb 02, 2023 7:09 am
by Thorwon
I've found a place that'll laser cut parts. So I sent them this drawing (the PDF) to see how good they do. I ordered 4 of them and it was under $100. That included zinc plating.
I'm pleased to report the parts are very nice. They came in a blister pack and well protected.
Now I need to know. Can use this reluctor with the 0411 as long as I use the correct CPS.
I'm hoping to be able get back to this little project next week. I'll post results when I can.
- reluctor.png (355.55 KiB) Viewed 2557 times
- reluctor 2.png (365.9 KiB) Viewed 2557 times
Re: 0411 running a 2.5L Jeep engine
Posted: Thu Feb 02, 2023 11:22 am
by DavidBraley
Very nice! How thick is that wheel?
Re: 0411 running a 2.5L Jeep engine
Posted: Thu Feb 02, 2023 11:41 am
by Thorwon
DavidBraley wrote:Very nice! How thick is that wheel?
It's 0.188 mild steel.
This is the company that made them.
https://sendcutsend.com/
Re: 0411 running a 2.5L Jeep engine
Posted: Thu Feb 02, 2023 2:33 pm
by DavidBraley
Thorwon wrote:DavidBraley wrote:Very nice! How thick is that wheel?
It's 0.188 mild steel.
This is the company that made them.
https://sendcutsend.com/
Thank you Sir!